Select Category
Brands
Jr Products Cabinet Door Strut, 2/Pk - 70545 - 342-70545F1
Used to assist in opening and holding cabinet doors open Stroke limit 1.10"
Jr Products Cabinet Door Strut, 2/Pk - 70555 - 342-70555F1
Used to assist in opening and holding cabinet doors open Also used to replace similar units with additional bracket on piston end
Jr Products Camp Casual Cc001 Rv Camping 12 Piece Outdoor Dinnerware Dish Set - Cc-001 - 342-Cc001F1
A 12 piece dish set complete with four dinner plates, four salad plates, and four bowls all tucked into a reusable carry-all, cardboard case. BPA Free, FDA approved, top rack dishwasher safe, and 100% sturdy melamine. Includes: (4) 11" Dinner Plates, (4) 8.5" Salad Plates, (4) 6" Bowls.
Jr Products Camp Casual Cc003 Rv Camping Outdoor Dinnerware Serving Bowl & Servers - Cc-003 - 342-Cc003F1
The perfect addition to any tailgate or party! Comes with one large serving bowl and two servers. Great for salads, chips, popcorn, you name it. FDA approved, BPA free, top rack dishwasher safe. 100% sturdy melamine.
Jr Products Camp Casual Cc004B Mug, Starry Night - Cc-004B - 342-Cc004Bf1
Did someone say coffee? Camp Casual's Into the Woods mug is the perfect addition to any road trip, RV adventure, or campsite! Made of heavy duty ceramic, The Mug is the perfect way to start any morning. 15 oz. capacitySturdy CeramicDishwasher & Microwave SafeFDA Approved
Jr Products Camp Casual Cc004C Mug, Wanderlust White - Cc-004C - 342-Cc004Cf1
Where will this weekend take you? Wherever you go Camp Casual's The Mug is the perfect companion to any RV or camping trip. Microwave and dishwasher safe. 15 oz. capacitySturdy CeramicDishwasher & Microwave SafeFDA Approved
Jr Products Camp Casual Cc004Pr Mug, Paws And Relax - Cc-004Pr - 342-Cc004Prf1
Take time to smell (and sip!) your coffee out of our retro inspired Airstream mug. The best breakfast companion and campfire coco mug! 15 oz. capacitySturdy CeramicDishwasher & Microwave SafeFDA Approved
Jr Products Camp Casual Cc004T Mug, Tangerine Trip - Cc-004T - 342-Cc004Tf1
Perfect for those cross country road trips, weekend warrior getaways, or just a relaxing Sunday at the campground! The Mug is microwaveable and dishwasher safe. 15 oz. capacitySturdy CeramicDishwasher & Microwave SafeFDA Approved
Jr Products Camp Casual Cc004Tl Mug, Bird'S Eye View - Cc-004Tl - 342-Cc004Tlf1
Snowcapped mountains are the perfect inspiration for some hot coffee or hot coco, right? Look no further than our Bird's Eye View mug to enjoy your tea, soup, chili, or even ice cream! A classic camper accessory that goes with every RV and campsite! 15 oz. capacitySturdy CeramicDishwasher & Microwave SafeFDA Approved
Jr Products Camp Casual Cc004Vb Mug, Vintage Blues - Cc-004Vb - 342-Cc004Vbf1
Our Vintage Blues mug brings the classic Airstream trailer to life with our beloved Mug. Perfect for coffee, tea, coco - even soup and chili! 15 oz. capacitySturdy CeramicDishwasher & Microwave SafeFDA Approved
Jr Products Camp Casual Cc005Rtg Throw, Road Trip, Gray - Cc-005Rtg - 342-Cc005Rtgf1
The softest, warmest, and coziest blanket for those chilly nights - whether you're around the campfire or relaxing in your RV, The Throw is the perfect addition for any outdoor (or indoor) adventure! The Throw comes in a reusable, plastic carrier perfect for travel or storage. Retro-inspired Road Trip print on front/Velvety soft Gray backing 100% polyester & 100% super soft 50"x60".
Jr Products Camp Casual Cc005Ss Throw, Serene Sequoia - Cc-005Ss - 342-Cc005Ssf1
The softest, warmest, and coziest blanket for those chilly nights - whether you're around the campfire or relaxing in your RV, The Throw is the perfect addition for any outdoor (or indoor) adventure! The Throw comes in a reusable, plastic carrier perfect for travel or storage. Oversized double sided velvety soft faux chinchilla fur 100% polyester & 100% super soft 60"x72" .
Jr Products Camp Casual Cc006 Nesting Bowls, Set Of 4 - Cc-006 - 342-Cc006F1
Camp Casual's nesting bowls come in a set of 4 complete with lids. They are made out of 100% heavyweight melamine, which is BPA free, FDA approved and top shelf dishwasher safe. The lids are made of plastic which are also BPA free. Great for storing leftovers, RVing, camping, boating and tailgating.
Jr Products Camp Casual Cc007R10 Eco-Friendly Paper Dinner Plates, Road Trip - Cc-007R10 - 342-Cc007R10F1
Durable disposable paper plates with our signature "Road Trip" vintage design. These heavy duty plates come in a 24 count pack and are microwavable, recyclable, compostable, and are cut/grease/water resistant. Made in USA!
Jr Products Camp Casual Cc007Rb Eco-Friendly Paper Bowls, Road Trip - Cc-007Rb - 342-Cc007Rbf1
Durable disposable 20 ounce paper bowls with our signature "Road Trip" vintage design. These heavy duty bowls come in a 24 count pack and are microwavable, recyclable, compostable, and are cut/grease/water resistant. Made in USA!
Jr Products Camp Casual Cc007W8 Eco-Friendly Paper Snack Plates, Into The Woods - Cc-007W8 - 342-Cc007W8F1
Durable disposable paper plates with our signature "Into the Woods" vintage design. These heavy duty plates come in a 24 count pack and are microwavable, recyclable, compostable, and are cut/grease/water resistant. Made in USA!
Jr Products Camp Casual Cc008Bp Throw, Buffalo Plaid - Cc-008Bp - 342-Cc008Bpf1
Keep up with the current trend with this richly colored black and red buffalo plaid throw! Made with luxurious fabric that is printed with the buffalo plaid on the front side, and coupled with a super soft black minky faux fur on the back side. Perfect for those chilly nights around the campfire. The throw measures 50" x 60" and comes in a poly bag for protection during shipping.
Jr Products Camp Casual Cc009 The Marine Dish Set - Cc-009 - 342-Cc009F1
Richly colored and vintage marine inspired graphics decorate this shatter resistant melamine BPA free set of dishes. Each set contains each: 11" dinner plates, 8" salad plates and 6" bowls.
Jr Products Cams - 10915 - 342-10915F1
Universal applications and used in conjunction with T and L Locking Handles. Lifetime warranty.
Jr Products Cams - 10925 - 342-10925F1
Universal applications and used in conjunction with T and L Locking Handles. Lifetime warranty.
Jr Products Catch Only, Black, 2/Pk - 11855 - 342-11855F1
Catch Only
Jr Products Catch Only, White, 2/Pk - 10855 - 342-10855F1
Catch Only
Jr Products Catch Only, Zinc, 2/Pk - 10835 - 342-10835F1
Catch Only
Jr Products Closet/Folding Door Latch/Strike, White - 81855 - 342-81855F1
Used on most accordion doors in RVs Requires 1/2" deep cut out in door or jambMounting screws includedLifetime Warranty
Jr Products Coax Cable Antenna For 35' Plus - Coax - 342-Coaxf1
Cable Antenna For 35ft PlusFor use with all Displays - SMA to Display, TNC for 6" whip antenna Includes:35 ft coax cable, straight wire whip antenna and mounting bracket for securing cable (includes two 1.25" self-tapping screws)
Jr Products Compartment Door Finger Pull - 195 - 342-00195F1
The universal door pull is made of rugged stainless steel for long-lasting durability. It is designed as a universal fit and will make operating your compartment doors easier. Lifetime warranty.
Jr Products Compartment Door Key Lock, 1-1/8" - 325 - 342-00325F1
Keyed alike using 751 style key Universal fit with flat and offset bladesChrome plated zinc unitsOriginal replacementLifetime warranty
Jr Products Compartment Door Key Lock, 1-3/8" - 335 - 342-00335F1
Keyed alike using 751 style key Universal fit with flat and offset bladesChrome plated zinc unitsOriginal replacementLifetime warranty
Jr Products Compartment Door Key Lock, 5/8" - 305 - 342-00305F1
Keyed alike using 751 style keyUniversal fit with flat and offset bladesChrome plated zinc unitsOriginal replacementLifetime warranty
Jr Products Compartment Door Key Lock, 7/8" - 315 - 342-00315F1
Keyed alike using 751 style keyUniversal fit with flat and offset bladesChrome plated zinc unitsOriginal replacementLifetime warranty
Jr Products Concealed Positive Catch - 70325 - 342-70325F1
The Concealed Positive Catch is an exact replacement for several cabinet overhead doors. It is constructed of durable, long-lasting plastic and is easily adjusted to provide a secure fit. Includes mounting screws. Lifetime Warranty.
Jr Products Cord Tensioner, 2/Pk - 81945 - 342-81945F1
Replaces Ascot and Specialty Window Coverings units Cords are compressed between inner/outer hubs for secure applicationUsed on any type of day/night shade where constant tension on cord is neededLifetime warranty
Jr Products Day/Night Shade Hold-Down, 2/Pk - 81735 - 342-81735F1
Our flush mount day/night shade hold-down is used to secure the tension cords on your shade. Comes complete with replacement screws to replace or repair and day/night shade hold-down. Lifetime warranty.
Jr Products Deluxe Assist Handle - 48315 - 342-48315F1
Grip area extended for greater security when entering your RV. Padded, rubber grip with molded finger area for comfort and safety. Includes plastic base pads for a professional installation. Lifetime warranty.
Jr Products Deluxe Compartment Door Key Lock, 1-1/8" - 175 - 342-00175F1
Keyed alike using J236 keyUniversal fit with flat and offset bladesOriginal replacementAutomotive style lock for a longer lifeWeather resistantLifetime warranty
Jr Products Deluxe Compartment Door Key Lock, 1-3/8" - 185 - 342-00185F1
Keyed alike using J236 keyUniversal fit with flat and offset bladesOriginal replacementAutomotive style lock for a longer lifeWeather resistantLifetime warranty
Jr Products Deluxe Compartment Door Key Lock, 5/8" - 155 - 342-00155F1
Keyed alike using J236 key Universal fit with flat and offset bladesOriginal replacementAutomotive style lock for a longer lifeWeather resistantLifetime warranty
Jr Products Deluxe Compartment Door Key Lock, 7/8" - 165 - 342-00165F1
Keyed alike using J236 keyUniversal fit with flat and offset bladesOriginal replacementAutomotive style lock for a longer lifeWeather resistantLifetime warranty
Jr Products Deluxe Window Frame Set For Rv Entry Door - 11011 - 342-11011F1
Better than OEM replacement Additional UV protection molded into the plastic to stop yellowingIncludes pre-applied butyl sealant for both door and window sealsWindow held in place by frame and butyl only, use caution when handling the glassIncludes both inside and outside piecesWindow opening: 12" x 21"Glass sold separatelyInstallation screws not included; use #6 flat head x 1-1/2" length. Needs 16.
Jr Products Deluxe Window Frame Set For Rv Entry Door - 11021 - 342-11021F1
Better than OEM replacement Additional UV protection molded into the plastic to stop yellowingIncludes pre-applied butyl sealant for both door and window sealsWindow held in place by frame and butyl only, use caution when handling the glassIncludes both inside and outside piecesWindow opening: 12" x 21"Glass sold separatelyInstallation screws not included; use #6 flat head x 1-1/2" length. Needs 16.
Jr Products Die Cast Metal Window Crank, 1-3/4" - 20275 - 342-20275F1
Will fit most applications. Made of die cast steel for long lasting use and come with a replacement screw. Lifetime warranty.
Jr Products Die Cast Metal Window Crank, 1" - 20265 - 342-20265F1
Will fit most applications. Made of die cast steel for long lasting use and come with a replacement screw. Lifetime warranty.
Jr Products Door Bumper - 11745 - 342-11745F1
Constructed of industrial rubber Measurement: 1" long x 1" baseUsed between screen and entry doorMounting screw includedLifetime warranty
Jr Products Double Roller Cabinet Catch - 70225 - 342-70225F1
This double roller catch can be used on any style of cabinet or door and is adjustable to provide a great fit. Includes mounting screws. Lifetime Warranty.
Jr Products Double Roller Catch W/Prong - 70235 - 342-70235F1
Double Roller Catch w/Prong can be installed on any style of door or cabinet to provide a positive catch. Made of durable steel and plastic rollers, it is a strong catch and adjustable for a great fit. Includes mounting screws. Lifetime Warranty.
Jr Products Double Rv Rocker Switch Assembly With Bezel - 12015 - 342-12015F1
Ratings: SPST, 16 Amp @ 125-250 VAC, 3/4 H.P @ 125-250 VAC, 10 Amp @ 14V (T)UL/CSA/VDE approvedCutout Dimensions:Single: 1.625" x 1.25" Double: 1.625" x 2.437"Triple: 1.625" x 3.625" Quad: 1.625" x 4.813"
Jr Products Double Rv Rocker Switch Assembly With Bezel - 12145 - 342-12145F1
Ratings: SPST, 16 Amp @ 125-250 VAC, 3/4 H.P @ 125-250 VAC, 10 Amp @ 14V (T)UL/CSA/VDE approvedCutout Dimensions:Single: 1.625" x 1.25" Double: 1.625" x 2.437"Triple: 1.625" x 3.625" Quad: 1.625" x 4.813"
Jr Products Double Rv Rocker Switch Assembly With Bezel - 12235 - 342-12235F1
Ratings: SPST, 16 Amp @ 125-250 VAC, 3/4 H.P @ 125-250 VAC, 10 Amp @ 14V (T)UL/CSA/VDE approvedCutout Dimensions:Single: 1.625" x 1.25" Double: 1.625" x 2.437"Triple: 1.625" x 3.625" Quad: 1.625" x 4.813"
Jr Products Drawer Slide Repair Kit - 70985 - 342-70985F1
Universal replacement drawer slide kit contains all of the plastic replacement parts needed to repair a sliding cabinet or desk drawer. Includes mounting screws. Lifetime warranty.
Jr Products Drawer Slide Socket Set C" Shape - 70725 - 342-70725F1
This drawer socket can be identified by looking at its opening where it resembles a larger "C" shape. It is an adjustable socket for a universal application. Includes mounting screws. Lifetime warranty.
Jr Products Drawer Slide Socket Set C" Shape - 70735 - 342-70735F1
This drawer socket can be identified by looking at its opening where it resembles a larger "C" shape. It is an adjustable socket for a universal application. Includes mounting screws. Lifetime warranty.
Jr Products Dust Plug For City Water Check Valve - 62105 - 342-62105F1
Universal, fits most city water fills Constructed of flexible 100% rubberFits Part #62115, 62125, 62135, 62145, 62155, 62165, 62175, 62185
Jr Products Efps130 Replacement Gas Spring End Fitting W/Snap-On Cap - Ef-Ps130 - 342-Efps130F1
Lifetime warranty.
Jr Products Efps30 Replacement Gas Spring End Fitting W/Steel Spring - Ef-Ps30 - 342-Efps30F1
Lifetime warranty.
Jr Products Efps90A Replacement Gas Spring Angled End Fitting - Ef-Ps90A - 342-Efps90Af1
Lifetime warranty.
Jr Products Elastic Sew-In Curtain Carrier - 81275 - 342-81275F1
Type C Curtain Carrier. Lifetime warranty.
Jr Products End Mount Trigger Latch For Rv Compartment Door - 10935 - 342-10935F1
High quality steel provides both security and durability. Replacement for any latch of the same configuration and basic size. Most commonly connected to a center mount operator assembly, using specially designed rods or with universal adjustable cables. Lifetime warranty.
Jr Products End Mount Trigger Latch For Rv Compartment Door - 10945 - 342-10945F1
High quality steel provides both security and durability. Replacement for any latch of the same configuration and basic size. Most commonly connected to a center mount operator assembly, using specially designed rods or with universal adjustable cables. Lifetime warranty.
Jr Products End Stop - Type D - 81385 - 342-81385F1
For use with track Type "D". Lifetime warranty.
Jr Products Exterior Tv Jack - 47755 - 342-47755F1
This unit comes with a 75 ohm F-Style connector and a flip-up door that stays open for easier access. It is constructed of durable polypropylene for a long life. Cutout Dim: 0.500" x 0.500"Outside Dim: 2.062" x 2.062"
Jr Products Fabric-To-Fabric Snap Kit, 6/Pk - 81575 - 342-81575F1
These units are used to add a snap attachment to any fabrics such as tarps, awning material or curtains. Use part #81565 tool kit to install. Lifetime warranty.
Jr Products Fabric-To-Wall Snap Kit, 6/Pk - 81585 - 342-81585F1
These units are used to add a snap attachment to any fabric or material where they are fastened to a wall or solid structure such as screen rooms, interior curtains, or security straps. Use Part #81565 tool kit to install. Lifetime warranty.
Jr Products Female Flare To Mpt Connector - 07-30225 - 342-0730225F1
3/8" Female Flare to 1/4" MPT Used to connect two LP Hoses or fittingsNot for potable water use (contains lead)
Jr Products Folding Shelf Bracket, White - 20725 - 342-20725F1
Sturdy support for any type of fold down shelf Supports up to 50 lbs.Lifetime warranty
Jr Products Free Swing Flush Mount Hinge, Satin Nickel - 70655 - 342-70655F1
Free swing cabinet door hinges are universal replacements for any flush mount application. Includes mounting screws. Lifetime warranty.
Jr Products Fx2K Pressurepro Fx Tpms, 2 Wheel Kit - Fx2K - 342-Fx2Kf1
The first TPMS designed specifically for towables, PULSE FX delivers PressurePro's first BYOD based system, arming users with market leading tire performance management at never-before-seen value. Allowing users to leverage existing smart devices to display real time readings and alerts directly through the free, PressurePro app, FX gives users: 24/7 tire performance monitoringFive unique alerts including Tire Pressure and Tire TemperaturePush notifications and FX warning lightUnit is sealed, and can be fully submerged in waterAbility to monitor up to 40 tiresVehicle naming and storage for easy monitoring of multiple trailersFully adjustable vehicle layout and displayFully customizable baseline and alerts KIT INCLUDES:PULSE FX DeviceDynamic Standard SensorsPULSE Fixed End Power CablePULSE Dipole AntennaFX Hook & Loop Mounting Pads
Jr Products Fx4K Pressurepro Fx Tpms, 4 Wheel Kit - Fx4K - 342-Fx4Kf1
The first TPMS designed specifically for towables, PULSE FX delivers PressurePro's first BYOD based system, arming users with market leading tire performance management at never-before-seen value. Allowing users to leverage existing smart devices to display real time readings and alerts directly through the free, PressurePro app, FX gives users: 24/7 tire performance monitoringFive unique alerts including Tire Pressure and Tire TemperaturePush notifications and FX warning lightUnit is sealed, and can be fully submerged in waterAbility to monitor up to 40 tiresVehicle naming and storage for easy monitoring of multiple trailersFully adjustable vehicle layout and displayFully customizable baseline and alerts KIT INCLUDES:PULSE FX DeviceDynamic Standard SensorsPULSE Fixed End Power CablePULSE Dipole AntennaFX Hook & Loop Mounting Pads
Jr Products Gfci Electrical Outlet, White - 15005 - 342-15005F1
UL/cUL approved
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2125-90 - 342-Gsni212590F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2200-90 - 342-Gsni220090F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-100 - 342-Gsni2300100F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-120 - 342-Gsni2300120F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-150 - 342-Gsni2300150F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-80 - 342-Gsni230080F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-90 - 342-Gsni230090F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2600-100 - 342-Gsni2600100F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4032-28 - 342-Gsni403228F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4033-30 - 342-Gsni403330F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4688-40 - 342-Gsni468840F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4983-35 - 342-Gsni498335F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4991-60 - 342-Gsni499160F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5000-20 - 342-Gsni500020F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5000-60 - 342-Gsni500060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5100-30 - 342-Gsni510030F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5100-40 - 342-Gsni510040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.GNSI-5100-40 is used on truck caps.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5150-20 - 342-Gsni515020F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5150-40 - 342-Gsni515040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5150-60 - 342-Gsni515060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-30 - 342-Gsni520030F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-40 - 342-Gsni520040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-50 - 342-Gsni520050F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.GSN5200-50 is used on truck caps.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-60 - 342-Gsni520060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-10 - 342-Gsni530010F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-20 - 342-Gsni530020F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-30 - 342-Gsni530030F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-40 - 342-Gsni530040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-50 - 342-Gsni530050F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-60 - 342-Gsni530060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-6624 - 342-Gsni6624F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-6642 - 342-Gsni6642F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.GSNI-6642 is used on truck caps.
