Tiedown Engineering
Tie Down Engineering Dock Side Cross Beam Extension - 86934 - 241-86934F1
With the addition of the Cross Beam 28 Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet wide.
Tie Down Engineering Dock Side Cross Beam Extension - 86916 - 241-86916F1
With the addition of the Cross Beam 28 Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet wide.
Tie Down Engineering Dock Hardware - Washer Plate - 26409 - 241-26409F1
Commercial grade. Should be used with every Angle. Two required for each Angle. 1-1/2"L x 5"H.
Tie Down Engineering Dock Hardware - Washer Plate - 24284 - 241-24284F1
Standard grade. Should be used with every Angle. Two required for each Angle. 1-1/2"L x 5"H.
Tie Down Engineering Dock Hardware - Steel Chain Pile Holder, Commercial Grade - 26419 - 241-26419F1
For use as a pile holder with 3/8" galvanized chain and shackles. Can be adjusted for various pile diameters. Size: 20-1/4" x 4-1/4" x 4-1/4" x 1/4" Steel.
Tie Down Engineering Dock Hardware - Piling Hoop And Roller Assembly, Commercial Grade - 26415 - 241-26415F1
Piling hoop & roller intended for areas with a lot of wind, current or tidal action. Combines the Piling hoop (26412) and roller assembly (26414) to make up for the up and down movement. For pilings up to 12" in diameter.
Tie Down Engineering Dock Hardware - Outside Pipe Holder - 26411 - 241-26411F1
Commercial grade. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set required for attaching.
Tie Down Engineering Dock Hardware - Outside Pipe Holder - 24280 - 241-24280F1
Standard grade. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set required for attaching.
Tie Down Engineering Dock Hardware - Outside Corner/Male 10"L X 5"H - 26522 - 241-26522F1
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab.
Tie Down Engineering Dock Hardware - Outside Corner/Male 10"L X 5"H - 26418 - 241-26418F1
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab.
Tie Down Engineering Dock Hardware - Outside Corner/Male 10"L X 5"H - 25491 - 241-25491F1
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab.
Tie Down Engineering Dock Hardware - Outside Corner/Female 10"L X 5"H - 26521 - 241-26521F1
Standard grade. Two 1/2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner/Female 10"L X 5"H - 26400 - 241-26400F1
Commercial grade. Two 1/2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner End - 26523 - 241-26523F1
Standard grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner End - 26428 - 241-26428F1
Commercial grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 12-1/4"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner End - 26402 - 241-26402F1
Commercial grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Male T Connector 5"L X 5"H - 26532 - 241-26532F1
Standard Grade w/ 1/2" tab. Use with Female T connector to attach fingers and ramps. Bolt set required for joint. Size: 5" x 5".
Tie Down Engineering Dock Hardware - Male T Connector 5"L X 5"H - 26427 - 241-26427F1
Commercial Grade w/ 3/4" tab. Use with Female T connector to attach fingers and ramps. Bolt set required for joint. Size: 5" x 5".
Tie Down Engineering Dock Hardware - Male T Connector 5"L X 5"H - 26408 - 241-26408F1
Commercial grade w/ 1/2" tab. Use with Female T connector to attach fingers and ramps. Bolt set required for joint. Size: 5"L x 5"H.
Tie Down Engineering Dock Hardware - Inside Corner Pipe Holder, Commercial Grade - 26405 - 241-26405F1
Commercial grade. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set for attaching. 2" Pipe.
Tie Down Engineering Dock Hardware - Inside Corner Pipe Holder, Commercial Grade - 26404 - 241-26404F1
Commercial grade. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set for attaching. 2" Pipe.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26524 - 241-26524F1
Standard grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 2" holes.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26417 - 241-26417F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 3" holes.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26403 - 241-26403F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 2-1/4" holes.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26401 - 241-26401F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ Square holes.
Tie Down Engineering Dock Hardware - Inside Corner 10-1/2"L X 5"H With 2-1/4" Elongated Holes And Larger Brace, Commercial Grade - 26424 - 241-26424F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 10-1/2"L x 5"H w/ 2-1/4" holes & larger brace.
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Lag Bolt Set (8 Per Bag) - 24292 - 241-24292F1
Commercial grade bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. Size: 3/8" x 5".
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Lag Bolt Set (8 Per Bag) - 24289 - 241-24289F1
Standard grade bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. Size: 3/8" x 3".
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Lag Bolt Set (8 Per Bag) - 24287 - 241-24287F1
Standard grade bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. Size: 3/8" x 2".
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Heavy Duty Piling Hoop, Commercial Grade - 26412 - 241-26412F1
Commerical grade. Heavy duty piling hoop for pilings up to 12" in diameter. The hoop is constructed of 1-1/2" pipe and is hot dip galvanized. It can be bolted directly to the side of the dock or to the optional deck plate.
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Carriage Bolt Set (8 Per Bag) - 26535 - 241-26535F1
Used to attach component parts. 3/8 x 2-1/2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3".
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Carriage Bolt Set (8 Per Bag) - 26534 - 241-26534F1
Used to attach component parts. 3/8 x 2-1/2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3".
Tie Down Engineering Dock Hardware - Heavy Duty Hot Dipped Galvanized 6" Roller Assembly, Commercial Grade - 26414 - 241-26414F1
Commercial heavy duty roller assembly. Bracket and roller bolt directly to the deck plate (26416). An aid to the up and down motion of the dock in areas of tidal action. 6" roller turns on a 5/8" diameter shaft. 3/4" bracket is hot-dipped galvanized. Size: 10-1/2" x 2".
Tie Down Engineering Dock Hardware - Heavy Duty 4" X 6" Deck Plate, Commercial Grade - 26416 - 241-26416F1
Heavy duty deck plate for use with Piling Hoop. This 3/16" thick 4"x 6" x 22" plate can be bolted from the top and side of the dock. The hoop can then be bolted to the deck plate, allowing it to be removed seasonally.
Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoop, Commercial Grade - 26429 - 241-26429F1
Commercial Grade w/4" radius for 8" Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 14" x 3".
Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoop, Commercial Grade - 26394 - 241-26394F1
Commercial Grade w/6" radius for12 Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 18" x 3".
Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoop, Commercial Grade - 26393 - 241-26393F1
Commercial Grade w/7" radius for 14" Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 20" x 3".
Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoop, Commercial Grade - 26391 - 241-26391F1
Commercial Grade w/5" radius for 10" Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 16" x 3".
Tie Down Engineering Dock Hardware - Galvanized Inside Rolling Ramp Bracket Includes Left And Right Ramp Brackets, Commercial Grade - 26431 - 241-26431F1
5" x 11" x 1/4" galvanized steel bracketIncludes left and right ramp brackets
Tie Down Engineering Dock Hardware - Galvanized Hex Head Bolt Set 3/4" X 3-1/2" (8 Per Bag) - 24279 - 241-24279F1
Standard grade. Includes lock nut. Used to connect male and female connectors. Galvanized 3/4" x 3-1/2".
Tie Down Engineering Dock Hardware - Galvanized Connector Pin Set 3/4" - 26531 - 241-26531F1
Standard grade. Used for quick disconnect of male and female connectors. Galvanized 3/4" connector pin and hitch clip pin.
Tie Down Engineering Dock Hardware - Female T Connector 5"L X 5"H - 26528 - 241-26528F1
Standard Grade w/ 1/2" tabs. Two welded 1/2" tabs. Bolts to side of dock to attach fingers and ramps. 5"L x 5"H.
Tie Down Engineering Dock Hardware - Female T Connector 5"L X 5"H - 26407 - 241-26407F1
Commercial grade w/ 1/2" tabs. Two welded 1/2" tabs. Bolts to side of dock to attach fingers and ramps. 5"L x 5"H.
Tie Down Engineering Dock Hardware - Chain Retainer, Commercial Grade - 26410 - 241-26410F1
Commercial grade. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H.
Tie Down Engineering Dock Hardware - Backing Plate/Hurricane Strap, Standard Grade - 26369 - 241-26369F1
Standard grade for use with Piling Hoops. Size: 2" x 18" x 7 ga.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26527 - 241-26527F1
Standard grade. Should be used for all cross supports. Each leg 2-1/2"L x 5"H.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26422 - 241-26422F1
Commercial grade. Should be used for all cross supports. Each leg 2-3/4"L x 5"H.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26406 - 241-26406F1
Commercial grade. Should be used for all cross supports. Each leg 2-1/2"L x 5"H.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26399 - 241-26399F1
Commercial grade. Should be used for all cross supports. Each leg 2-1/2"L x 2-1/2"H".
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26398 - 241-26398F1
Commercial grade. Should be used for all cross supports. Each leg 3"L x 5"H.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26397 - 241-26397F1
Commercial Grade. Should be used for all cross supports. Each leg 4"L x 8"H.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26392 - 241-26392F1
Commerical grade. Should be used for all cross supports. Each leg 2-3/4"L x 2-1/2"H.
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26380 - 241-26380F1
Commercial grade. Should be used for all cross supports. Each leg 4"L x 7"H".
Tie Down Engineering Dock Hardware - Angle Brackets/Clip - 26379 - 241-26379F1
Commercial grade. Should be used for all cross supports. Each leg 10"L x 3"H", 3 holes.
Tie Down Engineering Dock Hardware - 5" X 5" Back Up Plate, Commercial Grade - 26413 - 241-26413F1
Reinforcing plates are used to back up single T males and females. 5" x 5".
Tie Down Engineering Dock Hardware - 14" Steel Hoop Roller Pile Holder, Commercial Grade - 26423 - 241-26423F1
14" Commercial grade steel. The piling hoop secures around the piling, while roller permits smooth up and down movement.
Tie Down Engineering Dock Hardware - 14" Internal Pile Holder, Commercial Grade - 26434 - 241-26434F1
Commercial grade. Heavy duty 1/4" galvanized steel. Bolts to the dock directly. 4 Rollers allow it to move smoothly up and down the piling. Size: 24" x 24" x 7-15/16".
Tie Down Engineering Deluxe Anchor Kit Includes Anchor, Anchor Line, Chain And Shackles - 95096 - 241-95096F1
This anchor has the traditional holding power which has always been associated with Danforth® Standard® Anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long-lasting protection. Includes Danforth anchor, rope, stainless steel chain and shackles. Model S600 with 8 lb. Danforth® anchor for 17'-24' boats.
Tie Down Engineering Danforth Standard Anchor - 94016 - 241-94016F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 40S for 45' boat size.
Tie Down Engineering Danforth Standard Anchor - 94015 - 241-94015F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 22S for 40' boat size.
Tie Down Engineering Danforth Standard Anchor - 94014 - 241-94014F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 18S for 36' boat size.
Tie Down Engineering Danforth Standard Anchor - 94013 - 241-94013F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 13S for 31' boat size.
Tie Down Engineering Danforth Standard Anchor - 94012 - 241-94012F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 8S for 27' boat size.
Tie Down Engineering Danforth Standard Anchor - 94011 - 241-94011F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 4S for 17' boat size.
Tie Down Engineering Danforth Standard Anchor - 94010 - 241-94010F1
Have endured over 50 years giving reliable performance. Has the traditional good holding power which has always been associated with Danforth Standard anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped galvanized coating for long lasting protection. Model 2-1/2S for 10' boat size.
Tie Down Engineering Danforth Hi-Tensile Anchor - 94022 - 241-94022F1
Danforth's toughest, most durable anchor and features very high holding power. The flukes are fabricated for additional strength and then beveled to allow quick, deep bottom penetration. Shank is made from 4130 steel which treated for extra strength. Hot dipped galvanized finish. Model 35H for 64' boat size.
Tie Down Engineering Danforth Hi-Tensile Anchor - 94021 - 241-94021F1
Danforth's toughest, most durable anchor and features very high holding power. The flukes are fabricated for additional strength and then beveled to allow quick, deep bottom penetration. Shank is made from 4130 steel which treated for extra strength. Hot dipped galvanized finish. Model 20H for 50' boat size.
Tie Down Engineering Danforth Hi-Tensile Anchor - 94020 - 241-94020F1
Danforth's toughest, most durable anchor and features very high holding power. The flukes are fabricated for additional strength and then beveled to allow quick, deep bottom penetration. Shank is made from 4130 steel which treated for extra strength. Hot dipped galvanized finish. Model 12H for 42' boat size.
Tie Down Engineering Danforth Hi-Tensile Anchor - 94019 - 241-94019F1
Danforth's toughest, most durable anchor and features very high holding power. The flukes are fabricated for additional strength and then beveled to allow quick, deep bottom penetration. Shank is made from 4130 steel which treated for extra strength. Hot dipped galvanized finish. Model 5H for 31' boat size.
Tie Down Engineering Bunk Slicks - Black - 86170 - 241-86170F1
Attaches directly onto carpeted bunk boards. Fits 2" x 6" or 2" x 4" standard bunk boards. Slide on or off with less effort. Easy to install. Stainless mounting screws included.
Tie Down Engineering Bunk Slicks - Black - 86164 - 241-86164F1
Attaches directly onto carpeted bunk boards. Fits 2" x 6" or 2" x 4" standard bunk boards. Slide on or off with less effort. Easy to install. 40 Stainless mounting screws included.
Tie Down Engineering Bow Safety Chain 3/16" X 15-1/2" - 81201 - 241-81201F1
Connects the boat to the bow stand of the trailer. 3/16" x 12 links.
Tie Down Engineering Bolster Brackets - Sold As Pair - 81250 - 241-81250F1
Designed to support bolster or bunk boards. Slotted for vertical adjustment and feature non-slip dimples to avoid movement and increase load capacity.
Tie Down Engineering Bolster Brackets - Sold As Pair - 81220 - 241-81220F1
Designed to support bolster or bunk boards. Slotted for vertical adjustment and feature non-slip dimples to avoid movement and increase load capacity.
Tie Down Engineering Bolster Brackets - Sold As Pair - 81215 - 241-81215F1
Designed to support bolster or bunk boards. Slotted for vertical adjustment and feature non-slip dimples to avoid movement and increase load capacity.
Tie Down Engineering Bolster Brackets - Sold As Pair - 81210 - 241-81210F1
Designed to support bolster or bunk boards. Slotted for vertical adjustment and feature non-slip dimples to avoid movement and increase load capacity.
Tie Down Engineering Bolster Brackets - Sold As Pair - 81200 - 241-81200F1
Designed to support bolster or bunk boards. Slotted for vertical adjustment and feature non-slip dimples to avoid movement and increase load capacity.
Tie Down Engineering Bolster Brackets - Sold As Pair - 81195 - 241-81195F1
Designed to support bolster or bunk boards. Slotted for vertical adjustment and feature non-slip dimples to avoid movement and increase load capacity.
Tie Down Engineering 86588 Flare Teardrop Fender, Smooth Aluminum - 86588 - 241-86588F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86587 Teardrop Fender, Aluminum Tread - 86587 - 241-86587F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86586 Teardrop Fender, Smooth Aluminum - 86586 - 241-86586F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86585 Round Single Fender, Aluminum Tread - 86585 - 241-86585F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86584 Round Single Fender, Smooth Aluminum - 86584 - 241-86584F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86583 Jeep Single Fender, Aluminum Tread - 86583 - 241-86583F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86582 Jeep Single Fender, Smooth Aluminum - 86582 - 241-86582F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86581 Teardrop Fender, Steel - 86581 - 241-86581F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86580 Round Single Fender, Steel - 86580 - 241-86580F1
Heavy duty stamped fenders can be drilled to fit a variety of mounting options. Mounting hardware not included.
Tie Down Engineering 86576 Floating Guide Post, White - 86576 - 241-86576F1
The Floating Guide Post features the ability to adjust the overall height from 48 - 60 in. The user can choose to notch the post at a specific height or set on floatable mode and allow the waterline to naturally and automatically adjust the overall height as it enters/exits the water. This allows the post to always remain above the waterline and function regardless of the boat ramp inclination. The metal tube is made from heavy-duty 14 gauge steel, pre-galvanized, and powder coated for a durable finish. It features a 30 degree slant through the bottom 18 in. to allow for varying hull shapes. The PVC pipe in non-marring, black or white in color and designed to hide the floating slot and holes for a clean look.
Tie Down Engineering 86568 Floating Guide Post, Black - 86568 - 241-86568F1
The Floating Guide Post features the ability to adjust the overall height from 48 - 60 in. The user can choose to notch the post at a specific height or set on floatable mode and allow the waterline to naturally and automatically adjust the overall height as it enters/exits the water. This allows the post to always remain above the waterline and function regardless of the boat ramp inclination. The metal tube is made from heavy-duty 14 gauge steel, pre-galvanized, and powder coated for a durable finish. It features a 30 degree slant through the bottom 18 in. to allow for varying hull shapes. The PVC pipe in non-marring, black or white in color and designed to hide the floating slot and holes for a clean look.
Tie Down Engineering 86566 Tail Light Bracket - 86566 - 241-86566F1
Galvanized steel for long lasting durability.
Tie Down Engineering 86563 Vertical Bunk Bracket, 5" X 10" - 86563 - 241-86563F1
Ideal for aluminum trailers, vertical bunk brackets are made of 1/4" hot dipped galvanized steel for long lasting protection.
Tie Down Engineering 86562 Vertical Bunk Bracket, 5" X 8" - 86562 - 241-86562F1
Ideal for aluminum trailers, vertical bunk brackets are made of 1/4" hot dipped galvanized steel for long lasting protection.
Tie Down Engineering 86429 Hull Sav'R Ribbed Wobble Roller, Black, 5" - 86429 - 241-86429F1
Hull SaVür ribbed wobble rollers. Constructed of colored enhanced polyvinyl chloride. Limited lifetime warranty against cutting and fading.
Tie Down Engineering 86428 Hull Sav'R Smooth Wobble Roller, Black, 4" - 86428 - 241-86428F1
Hull SaVür smooth wobble roller. Constructed of colored enhanced polyvinyl chloride. Limited lifetime warranty against cutting and fading.
Tie Down Engineering 86427 Hull Sav'R Ribbed Wobble Roller, Black, 4" - 86427 - 241-86427F1
Hull SaVür ribbed wobble rollers. Constructed of colored enhanced polyvinyl chloride. Limited lifetime warranty against cutting and fading.
Tie Down Engineering 86418 Hull Sav'R Poly Vinyl Keel Pad, Black - 86418 - 241-86418F1
Poly vinyl pads are long lasting, will absorb shock, are cut resistant and will not mark or mar your boat.
Tie Down Engineering 86291 Hull Sav'R Poly Vinyl Keel Pad, Amber - 86291 - 241-86291F1
Poly vinyl pads are long lasting, will absorb shock, are cut resistant and will not mark or mar your boat.
Tie Down Engineering 86277 Hull Sav'R Ribbed Wobble Roller, Amber, 4" - 86277 - 241-86277F1
Hull SaVür ribbed wobble rollers. Constructed of colored enhanced polyvinyl chloride. Limited lifetime warranty against cutting and fading.
Tie Down Engineering 86269 Aluminum Adjustable Teardrop Fender - 86269 - 241-86269F1
Heavy duty fenders made from .083" gauge diamond plate aluminum. Tandem tear drop trailer fender can be adjusted from 60" to 72". Mounting hardware not included.
Tie Down Engineering 86267 Galvanized Metal Fender - 86267 - 241-86267F1
Heavy duty stamped 16 gauge galvanized steel. Fenders can be drilled to fit a variety of mounting options. Mounting brackets sold separately.
