Select Category
Brands
121/T-8 Spraying Thinner-Quart - 11212108 - 93-121Qf1
121 Spray Thinner for Antifouling is a fast evaporating thinner used to reduce products before spray application. The thinner flashes out rapidly.
121/T-8 Spraying Thinner-Gal - 11212106 - 93-121Gf1
121 Spray Thinner for Antifouling is a fast evaporating thinner used to reduce products before spray application. The thinner flashes out rapidly.
120/T-10Q Brushing Thinner-Qt - 211212008 - 93-120Caqf1
A general purpose thinner. Many paints when stored for some time before use will increase in viscosity and should be thinned. Evaporates at a moderatre rate and is completely out of the paint film in several hours
120/T-10Q Brushing Thinner-Qt - 11212008 - 93-120Qf1
A general purpose thinner. Many paints when stored for some time before use will increase in viscosity and should be thinned. Evaporates at a moderatre rate and is completely out of the paint film in several hours
120/T-10 Brushing Thinner-Gal - 11212006 - 93-120Gf1
A general purpose thinner. Many paints when stored for some time before use will increase in viscosity and should be thinned. Evaporates at a moderatre rate and is completely out of the paint film in several hours
120-Rmam Series Fuel / Water Separator - 120Rmam30 - 62-120Rmam30F1
The 120RMAM fuel filter/water separator features a unitized mounting bracket for mounting versatility and 2 inlet/outlet ports. It also features an Aquabloc® II replacement element that repels water and removes solid contamination.
12° Tilt Bronze Thru-Hull Ducer - 010-10982-21 - 322-0101098221F1
Dual frequency (50/200kHz) transducer is specially designed to provide a vertical beam without a fairing block. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for more accurate depth readings. The nearly flush housing minimizes drag with only 3/16" extending outside of the hull. Includes a built-in temp sensor and handles up to 600 watts (RMS) power. Includes 39' cable.
12# Flash Weight - 2295190 - 627-2295190F1
Cannon Trolling Flash Weights™ incorporate a flashing prism design for extra lure power. They are black vinyl coated. The Keel keeps weight tracking accurately and prevents cable twisting.
12"L X 9"W Replacement Standard Blade Only - 20159-001 - 622-20159001F1
Replacement SS Standard Blade Only
12" X 9" Edge Mount Electric Trim Tab Kit W/O Switch - 15015-101 - 622-15015101F1
Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 12" long models 11". Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardware Switch kit sold separatelyStainless steel mounting hardwareSwitch kit sold separately
12" X 30" Trim Tab Kit W/O Switch - 15010-101 - 622-15010101F1
Lenco trim tabs makes your boat ride smoother, drier, faster and with increased safety. Lenco's ballscrew design is reliable, powerful, and features an instant response which makes it very user friendly.Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are constructed of 12 guage, 304 stainless steel with a 5/8" flared trailing edge. Minimum transom height: 14".Kit Includes:Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsAll stainless steel mounting hardware Kit Includes:Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsStainless steel mounting hardwareSwitch kits sold separately
12" X 18" Trim Tab Kit W/O Switch - 15008-101 - 622-15008101F1
Lenco trim tabs makes your boat ride smoother, drier, faster and with increased safety. Lenco's ballscrew design is reliable, powerful, and features an instant response which makes it very user friendly.Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are constructed of 12 guage, 304 stainless steel with a 5/8" flared trailing edge. Minimum transom height: 14".Kit Includes:Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsAll stainless steel mounting hardware Kit Includes:Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsStainless steel mounting hardwareSwitch kits sold separately
12" X 18" Replacement Standard Blade Only - 20161-001 - 622-20161001F1
Replacement SS Standard Blade Only
12" X 18" Jolly Roger Flag - 1818 - 32-1818F1
1-sided Perma-print nylon flag with brass grommets.
12" X 18" Edge Mount Electric Trim Tab Kit W/O Switch - 15017-101 - 622-15017101F1
Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 12" long models 11". Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardware Switch kit sold separatelyStainless steel mounting hardwareSwitch kit sold separately
12" X 18" Cocktail Flag - 9118 - 32-9118F1
1-sided Perma-print nylon flag with brass grommets.
12" X 18" Beer Flag - 9218 - 32-9218F1
1-sided Perma-print nylon flag with brass grommets.
12" X 12" Trim Tab Kit W/O Switch - 15007-101 - 622-15007101F1
Lenco trim tabs makes your boat ride smoother, drier, faster and with increased safety. Lenco's ballscrew design is reliable, powerful, and features an instant response which makes it very user friendly.Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are constructed of 12 guage, 304 stainless steel with a 5/8" flared trailing edge. Minimum transom height: 14".Kit Includes:Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsAll stainless steel mounting hardware Kit Includes:Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsStainless steel mounting hardwareSwitch kits sold separately
12" X 12" Trim Tab Kit W/Led Indicator Switch - 15109-103 - 622-15109103F1
Lenco trim tabs makes your boat ride smoother, drier, faster and with increased safety. Lenco's ballscrew design is reliable, powerful, and features an instant response which makes it very user friendly.Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are constructed of 12 guage, 304 stainless steel with a 5/8" flared trailing edge. Minimum transom height: 14". Kit Includes: Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsAll stainless steel mounting hardwareSwitch KitSwitch Kit
12" X 12" Trim Tab Kit W/Double Rocker Swtch - 15103-104 - 622-15103104F1
Lenco trim tabs makes your boat ride smoother, drier, faster and with increased safety. Lenco's ballscrew design is reliable, powerful, and features an instant response which makes it very user friendly.Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are constructed of 12 guage, 304 stainless steel with a 5/8" flared trailing edge. Minimum transom height: 14". Kit Includes: Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsAll stainless steel mounting hardwareSwitch KitSwitch Kit
12" X 12" Std Tab Kit W/Standard Tactile Switch - 15105-102 - 622-15105102F1
Lenco trim tabs makes your boat ride smoother, drier, faster and with increased safety. Lenco's ballscrew design is reliable, powerful, and features an instant response which makes it very user friendly.Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are constructed of 12 guage, 304 stainless steel with a 5/8" flared trailing edge. Minimum transom height: 14". Kit Includes: Waterproof plug and play Deutsch connectors12 -volt actuators (2) with 6 foot leads2 stainless steel trim tab planes-12 gauge20' actuator extension harnesses (2) with Deutsch connectorsAll stainless steel mounting hardwareSwitch KitSwitch Kit
12" X 12" Replacement Standard Blade Only - 20149-001 - 622-20149001F1
12 x 12 Replacement Standard Blade Only
12" X 12" Edge Mount Electric Trim Tab Kit W/O Switch - 15016-101 - 622-15016101F1
Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 12" long models 11". Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardware Switch kit sold separatelyStainless steel mounting hardwareSwitch kit sold separately
12" X 12" Edge Mount Electric Trim Tab Kit W/Led Indicator Switch - 15110-103 - 622-15110103F1
Fast response electric actuators for precise control. Fully submersible. All plug & play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 11". 2" Hinge height. Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardwareLED Indicator Switch KitSwitch Kit
12" X 12" Edge Mount Electric Trim Tab Kit W/124 Switch - 15106-102 - 622-15106102F1
Fast response electric actuators for precise control. Fully submersible. All plug & play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 11". 2" Hinge height. Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardware124 Switch KitSwitch Kit
12" X 12" Edge Mount Electric Trim Tab Kit W/122 Switch - 15102-104 - 622-15102104F1
Fast response electric actuators for precise control. Fully submersible. All plug & play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 11". 2" Hinge height. Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardware122 Switch KitSwitch Kit
12" X 12" Edge Mount Electric Electropolished Trim Tab Kit W/O Switch - 15116-101 - 622-15116101F1
Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades are 304 stainless steel with 1" turned up edges and an 85° inside taper. Edge mount tabs are space savers. The actuators mount at the trailing edge of the blades, requiring less transom height than the standard mount tabs. Min transom height: 12" long models 11". Kit Includes: 12-volt actuators (2) with 6' leads and Deutsch connectors20' actuator extension harnesses (2) with Deutsch connectorsStainless Steel trim tab blades, 12 gauge (2)Stainless Steel mounting hardware Switch kit sold separatelyStainless steel mounting hardwareSwitch kit sold separately
12" Triple Fender Holder Kit - 19-270-517 - 218-Tfr2803F1
Made of stainless steel and fits most popular fender sizes. The fender holders and two styles of connectors are sold separately, so you can custom configure your fender storage system without having to buy extra hardware you won't be using. 3 Fender holder kits fit 7/8"-1" rail systems only. For larger rail systems, Order components separately.
12" Stealth Series Led Bi-Color Pole Light - 1617Dp2Blk - 9-1617Dp2Blkf1
Removable bi-color pole light. 12V. USCG certified for use on power vessels under 12 m (39.4 ft). One mile visibility. Stainless steel top, 3/4" diameter aluminum pole with 0° RakeStow-a-way plug-in type pole. Requires 2 pin mounting baseGold plated contactsDesigned to also fit most other manufacturer's basesLocking collar
12" Stainless Steel Stud Mount Hand Rails - 254112-1 - 354-2541121F1
Formed 304 stainless steel. 2" Rail height.
12" Electric Drum Brakes - 82088 - 641-82088 Superseded By: 641-K71G0105F1
Electric brakes offer braking in forward and reverse. Features water resistant connections, rubber molded plugs, and quick switch electrical connections for fast and easy installation. Sold in pairs left and right. Mounting nuts and bolts included.
12" Dual Fender Holder Kit - 28-785-655 - 218-Tfr2802F1
Made of stainless steel and fits most popular fender sizes. The fender holders and two styles of connectors are sold separately, so you can custom configure your fender storage system without having to buy extra hardware you won't be using.2 Fender holder kits fit 7/8"-1" rail systems only. For larger rail systems, Order components separately.
12" Drum Brake Replacement Parts Kit - 81095 - 641-81095 Superseded By: 641-K71G0022F1
12" Downrigger Pedestal Riser - 2612 - 736-2612F1
Made from fibre reinforced nylon and stainless steel 2" tubing for the ultimate in strength. Designed to be used with all of our downrigger mounts. Plate Dimensions: 5-1/2" x 5-1/2". Bolting Dimensions: 4-1/2" x 3-1/2"
12" Bi-Color Pole Light - 1612Dp2Blk - 9-1612Dp2Blkf1
USCG certified for use on power driven vessels under 12 meters (39.4 ft). length. 1 mile visibility. USCG, ABYC, NMMA Certified.Black plastic top. 3/4" dia. anodized aluminum tube. 12V bulb included. Requires 2 pin mounting base. Ideal for boats with casting decks on the bow. Can be unplugged and stowed while fishing. This leaves only a small, flat topped base.
12'Mach-36 Mercury Ii Gen Cable - Mach36X12 - 216-Mach36X12F1
For Mercury and Mercury Gen II series controls. Heavy duty 18 laywire conduit for long life & high efficiency for smooth operation and reduced bend radius. Ideal for long complex cable runs. High resistance blue outer jacket protects against abrasion, UV and chemicals. 3.4" Stroke.
12' X 100' Clear Poly Sheeting 4Mil. - Cf0412C - 28-Cf0412Cf1
Great for covering boats for inside storage or for use under boats to collect barnacles, etc.
12' Dometic O/B Hose Kit, Pair - Ho5112 - 1-Ho5112F1
Includes two hoses - can be used with all Dometic systems, except SeaStar PRO, BayStar, Capilano and 3-line inboard systems. ID of 5/16".
12' Accutech Zerotorque Feedback Rack Steering System - Accutech12 - 216-Accutech12F1
The patented ZeroTorque Feedback clutch eliminates rudder torque at the steering wheel. A perfect solution for boats without power assist or any boat with moderate rudder torque. This 3.5 turn lock to lock package delivers smooth steering with minimal lost motion.Includes:M86 - preassembled helm with steering cableG88NR® - non-reversible shaft assemblyX34 - 90° bezel
12-1/2" Removable Bi-Color Light With Utility Light, 5 Degree Rake - 1212Dp2Chr - 9-1212Dp2Chrf1
USCG certified for use on sail or power driven vessels under 12 meter (39.4') 1 mile visibility3/4" diameter anodized aluminum tubesDeck illuminating utility light, 12 V bulb includedStow-a-way plug in type pole w/gold plated contacts
12-1/2" Removable Bi-Color Light With Utility Light, 0 Degree Rake - 1211Dp2Chr - 9-1211Dp2Chrf1
USCG certified for use on sail or power driven vessels under 12 meter (39.4') 1 mile visibility3/4" diameter anodized aluminum tubesDeck illuminating utility light, 12 V bulb includedStow-a-way plug in type pole w/gold plated contacts
12 X14 X2 Epdm Pad Ea. - Jbp-1214.2 - 375-Jbp12142F1
Stromberg Carlson JBP12142 Base Pad, 12" x 14" x 2"
12 X14 X1 Epdm Pads 2Pk - Jbp-1214.1 - 375-Jbp12141F1
Stromberg Carlson JBP12141 Base Pads, 12" x 14" x 1", 2/pk
12 X 600' Anti-Chafe Tape - 1515P-Bw12-600 - 315-Bw12600F1
A high performance polyethylene film with a "light tack" adhesive providing a tough, puncture resistant barrier preventing scratching or chafing. This tape is designed to leave no residue while providing a UV protected surface between the shrink wrap and the covered object. APPLICATIONS: Anti chafe tape is applied to surfaces under the shrink wrap. It is not a heat shrinkable product.
12 Side Mt Wind Adj Pr - 1290Dp0Chr - 9-1290Dp0Chrf1
Chrome plated zinc with black plastic knob. Overall 12" long. Adjustment length is 9-1/2". Screw size is #8.
12 S/S Handrail - H-001A - 332-H001Af1
Tubular stainless steel, buffed to prevent corrosion. Easy to mount anywhere there is access to a thru-bolt. Made with 2" x 5/16" studs and mounts flush with included hardware. Lifetime guarantee. Made in the USA.
12 Premium Mooring Buoy - 4400-W - 58-4400F1
Rock hard outer shell, seamless & almost indestructible. Core is 3 lb. high density polyurethane foam. All eyebolts are hot-dipped galvanized medium carbon steel. Eyebolts are permanently bonded inside buoy preventing wear and eventual loss of floatation.
12 Oz. Glass Fabric 60" X 10 Yd - 745-10 - 655-74510F1
Woven glass fabrics are ideal for building composite laminates and repairing fiberglass structures. May also be used to provide an abarasion-resistant covering for wooden structures. When wet-out, the 4 oz. and 6 oz. fabrics become transparent, allowing a clear, natural wood finish. May be painted or varnished.
12 Oz. Glass Fabric 30" X 30" - 745-30 - 655-74530F1
Woven glass fabrics are ideal for building composite laminates and repairing fiberglass structures. May also be used to provide an abarasion-resistant covering for wooden structures. When wet-out, the 4 oz. and 6 oz. fabrics become transparent, allowing a clear, natural wood finish. May be painted or varnished.
12 Offset Mt Wind Adj Pr - 1291Dp0Chr - 9-1291Dp0Chrf1
Chrome plated zinc with black plastic knob. Overall 12" long. Adjustment length is 9-1/2". Screw size is #8.
12 Keel Roller - Rp-12 - 122-Rp12F1
Durable orange polyurethane. Will not mark or discolor boat. Cut and abrasion resistant. Will not "flat spot" even after months of storage. Roller is unaffected by grease, oil, gasoline, exhaust fumes, salt, etc. No bushings to pop out. Continuous bearings and reinforcing tubes on rollers over 7" long are completely enclosed in polyurethane. Shafts should be greased at installation.
12 Ga Water Heater, 120V W/O Heat Exchanger - 171201 - 78-171201F1
Feature an attractive polymer jacket that will not corrode from the dampness below deck. Jacket is flame retardant and resists damage during installation and handling. Adjustable thermostat controls water temperature. Glass lined steel tank is more durable than stainless steel. Replaceable anode for electrolysis protection. Five year limited warranty on tanks. 120 VAC, 1250W.
12 Ga Water Heater W/Heat Exchanger - 171211 - 78-171211F1
Feature an attractive polymer jacket that will not corrode from the dampness below deck. Jacket is flame retardant and resists damage during installation and handling. Adjustable thermostat controls water temperature. Glass lined steel tank is more durable than stainless steel. Replaceable anode for electrolysis protection. Five year limited warranty on tanks. 120 VAC, 1250W.
12 Aluminum Drop Hitch Ball Hitch Ball Included Bell - Trz12Al - 255-Trz12Alf1
Machined From Solid Billit AluminumAdjusts in 1" increments10,000 lbs Tow Rating, Ball Limited1,500 lbs Max Tounge WeightContains Keyed Alike 5/8 Receiver Lock, T3 and Dual Hitch ball (2" & 2-5/15")
12 - 305Mm Fender Holder - 03-170-882 - 218-Tfr280F1
Made of stainless steel and fits most popular fender sizes. The fender holders and two styles of connectors are sold separately, so you can custom configure your fender storage system without having to buy extra hardware you won't be using.
116X11Cp Stainless Cotter Pins, 1/16" X 1", 100/Box - 5080-047 - 828-116X11Cpf1
18-8 stainless steel.
110Tt 12V Thruster Kit, 1.5Kw - 591102 - 239-591102F1
Thrusters give you total control of your boat when docking and departing regardless of wind or current conditons. No reservoir to install, no leaks and no maintenanceHigh integrity sealBlack box electronics protect motorHardened and ground spiral bevel gear for maximum efficiency and quiet power transmissionSelf resetting thermal protection on all motorsEasy plug together switch connectionsMinimum silhouette hub for smooth water flowIncludes a spline driven, high performance, 5-blade propeller which gives equal thrust in both directionsA complete system Requires a thruster unit, control panel, control cable, fuse holder, fuse and tunnel. 591102 is sold as a complete kit including the 140TT 1.5kW thruster, fuse and fuse holder, 7m control cable, joystick and 589402 tunnel.
110 Lb. Horizon Claw Anchor - 57950 - 239-0057950F1
Patterned after anchors used to secure oil rigs in the North Sea. Can be used very effectively in a variety of sea beds and remains stable under a variety of tide and wind conditions. Stows easily. Cast Steel.
11" Nylon Standard Cable Tie, 25 Pcs. Natural - 50-14271 - 50-14271F1
Natural Cable Ties
11" Lock'N-Pin 3/4" Fixed Height Post, Bulk - 2114 - 148-2114F1
Fixed height 3/4" pin post. 1.5" diameter brushed aluminum posts. Steel pin.
11" Lock'N-Pin 3/4" Fixed Height Post - Sp-2114 - 148-Sp2114F1
Fixed height 3/4" pin post. 1.5" diameter brushed aluminum posts. Steel pin.
11" Extension Hose For Grease Gun - 28800 - 74-28800F1
Ideal for lubricating hard-to-reach fittings. Works with most grease guns. Flexible to work at odd angles.
11' Accutech Zerotorque Feedback Rack Steering System - Accutech11 - 216-Accutech11F1
The patented ZeroTorque Feedback clutch eliminates rudder torque at the steering wheel. A perfect solution for boats without power assist or any boat with moderate rudder torque. This 3.5 turn lock to lock package delivers smooth steering with minimal lost motion.Includes:M86 - preassembled helm with steering cableG88NR® - non-reversible shaft assemblyX34 - 90° bezel
11-Mach-36 Mercury Ii Gen Cable - Mach36X11 - 216-Mach36X11F1
For Mercury and Mercury Gen II series controls. Heavy duty 18 laywire conduit for long life & high efficiency for smooth operation and reduced bend radius. Ideal for long complex cable runs. High resistance blue outer jacket protects against abrasion, UV and chemicals. 3.4" Stroke.
11 Lb. Horizon Claw Anchor - 57905 - 239-0057905F1
Patterned after anchors used to secure oil rigs in the North Sea. Can be used very effectively in a variety of sea beds and remains stable under a variety of tide and wind conditions. Stows easily. Cast Steel.
10X78P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 7/8", 100/Box - 5163-192 - 828-10X78P12Smf1
18-8 stainless steel.
10X58P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 5/8", 100/Box - 5163-190 - 828-10X58P12Smf1
18-8 stainless steel.
10X58F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 5/8", 100/Box - 5162-190 - 828-10X58F12Smf1
18-8 stainless steel.
10X3F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 3", 100/Box - 5162-204 - 828-10X3F12Smf1
18-8 stainless steel.
10X34P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 3/4", 100/Box - 5163-191 - 828-10X34P12Smf1
18-8 stainless steel.
10X34O12Sm Stainless Sheet Metal Screws, Oval Head, #10 X 3/4", 100/Box - 5165-191 - 828-10X34O12Smf1
18-8 stainless steel.
10X34F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 3/4", 100/Box - 5162-191 - 828-10X34F12Smf1
18-8 stainless steel.
10X312P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 3-1/2", 100/Box - 5163-206 - 828-10X312P12Smf1
18-8 stainless steel.
10X312F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 3-1/2", 100/Box - 5162-206 - 828-10X312F12Smf1
18-8 stainless steel.
10X2P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 2", 100/Box - 5163-200 - 828-10X2P12Smf1
18-8 stainless steel.
10X2F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 2", 100/Box - 5162-200 - 828-10X2F12Smf1
18-8 stainless steel.
10X212F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 2-1/2", 100/Box - 5162-202 - 828-10X212F12Smf1
18-8 stainless steel.
10X2.25 Lh Electric Brake 3.5K - 296649 - 804-296649F1
The all new Forward Self Adjusting brakes provide optimal braking performance and enhanced brake lining and magnet wear. The brakes automatically forward adjust with every stopping motion to ensure proper braking and increased safety. No manual adjustment is needed and maintenance costs are lowered. Have peace of mind knowing that at 60 mph your braking will improve by 50%. Complete Kit includes backing plate, shoe and linings, magnet, actuating lever, adjusting screw, spring hardware, sealed wire connectors, and mounting fasteners.
10X1P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 1", 100/Box - 5163-193 - 828-10X1P12Smf1
18-8 stainless steel.
10X1O12Sm Stainless Sheet Metal Screws, Oval Head, #10 X 1", 100/Box - 5165-193 - 828-10X1O12Smf1
18-8 stainless steel.
10X1F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 1", 100/Box - 5162-193 - 828-10X1F12Smf1
18-8 stainless steel.
10X134P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 1-3/4", 100/Box - 5163-199 - 828-10X134P12Smf1
18-8 stainless steel.
10X134F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 1-3/4", 100/Box - 5162-199 - 828-10X134F12Smf1
18-8 stainless steel.
10X13 White Abs Oval Sink Bell Rv Rvx - 16156Pw - 135-16156Pwf1
10X12P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 1/2", 100/Box - 5163-189 - 828-10X12P12Smf1
18-8 stainless steel.
10X12F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 1/2", 100/Box - 5162-189 - 828-10X12F12Smf1
18-8 stainless steel.
10X114P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 1-1/4", 100/Box - 5163-195 - 828-10X114P12Smf1
18-8 stainless steel.
10X114O12Sm Stainless Sheet Metal Screws, Oval Head, #10 X 1-1/4", 100/Box - 5165-195 - 828-10X114O12Smf1
18-8 stainless steel.
10X114F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 1-1/4", 100/Box - 5162-195 - 828-10X114F12Smf1
18-8 stainless steel.
10X112P12Sm Stainless Sheet Metal Screws, Pan Head, #10 X 1-1/2", 100/Box - 5163-197 - 828-10X112P12Smf1
18-8 stainless steel.
10X112F12Sm Stainless Sheet Metal Screws, Flat Head, #10 X 1-1/2", 100/Box - 5162-197 - 828-10X112F12Smf1
18-8 stainless steel.
10W40 Fcw 4-Cycle Outboard Synthetic Blend Oil, 55 Gal. Drum - 18-9551-7 - 47-95517F1
NMMA FC-W / API SL oils for use in all outboard and inboard applications without a catalytic converter. These oils provide superior protection to marine engines. Provides the additional protection from rust and corrosion found in the marine environment along with high load carrying capabilities. Sold in case packs only.
10W40 Fcw 4-Cycle Outboard Synthetic Blend Oil, 16 Gal. Drum - 18-9551-6 - 47-95516F1
NMMA FC-W / API SL oils for use in all outboard and inboard applications without a catalytic converter. These oils provide superior protection to marine engines. Provides the additional protection from rust and corrosion found in the marine environment along with high load carrying capabilities. Sold in case packs only.
10W30 Full Synthetic Oil 55G Not Sold In Canada - 8M0173225 - 710-92-8M0173225F1
10Inhsg. W/Gac Crtdg Mnt Brk S Bell Rv Rvx - Poe12Ghgacb-Rv - 555-Poe12Ghgacbrvf1
105690 Shurtape Frogtape® Fls 325 Yellow Low-Stretch Pvc Fineline Masking Tape, 36 Yards - 105690 - 507-105690F1
Performance grade, low-stretch PVC fineline masking tape designed for use in transportation, marine and automotive OEM and aftermarket finishing applications. Provides a tough, yet conformable, waterproof and solvent-resistant solution to deliver crisp, fineline edges without staining or ghosting. Waterproof and solvent-resistantTough and conformableCrisp, fineline edgeCan withstand high-temperature bake cycles (325 F up to 45 min)
1045P0Sdp Plug-In Type Base, Ss, 2Pin - 1045P0Sdp - 9-1045P0Sdpf1
Polished Stainless SteelBlack PolymerWaterproof Snap-On CoverFits 3/4" Poles with Locking CollarPigtail LeadsFig. 1045 (2 Pin)Fits: 1343, 1347, 1348, 1349, 1400, 1440, 1442, 1444, 1450, 1451, 1452, 1460, 1454, 1470 Series All-Round Pole Lights 1612 and 1616 Series Bi-Color Pole Lights
104+® 10406 Octane Boost, 16 Oz., 6/Case - 10406 - 269-10406F1
Boosts Power Get Better Gas MileageCleans Fuel InjectorsReduces Knocks, Pings & HesitationSafe for Catalytic Converters & Oxygen Sensors
10321Ln Stainless Steel Nyloc Nuts, 10-32, 100/Box - 5034-011 - 828-10321Lnf1
18-8 stainless steel.
10321Hn Stainless Steel Hex Nuts, 10-32, 100/Box - 5035-011 - 828-10321Hnf1
18-8 stainless steel.
10241Ln Stainless Steel Nyloc Nuts, 10-24, 100/Box - 5034-010 - 828-10241Lnf1
18-8 stainless steel.
10241Hn Stainless Steel Hex Nuts, 10-24, 100/Box - 5035-010 - 828-10241Hnf1
18-8 stainless steel.
10241An Stainless Steel Acorn Nuts, 10-24, 100/Box - 5037-010 - 828-10241Anf1
18-8 stainless steel.
10241 Stainless Steel Wing Nuts, 10-24, 100/Box - 5038-010 - 828-10241Wnf1
18-8 stainless steel.
101Lw Stainless Steel Lock Washers, #10, 100/Box - 5058-010 - 828-101Lwf1
18-8 stainless steel.
101Fw Stainless Steel Flat Washers, #10, 100/Box - 5055-210 - 828-101Fwf1
18-8 stainless steel.
101Cw Stainless Steel Finsh (Cup) Washers, #10, 100/Box - 5056-975 - 828-101Cwf1
18-8 stainless steel.
1000 Gph Ultima Automatic Bilge Pump - 32-47260-003 - 189-3247260003F1
Sleek, reliable and compact unit with integrated Ultima switch ready to install and run for years of service.Patented Mirus field detector cellsNo exposed sensors, eliminates corrosion possibilitiesNot affected by oil or foreign debrisIncludes both a straight and 90° smooth elbow Dura-Port and a removable check valveMade in USA.
1000 Gph Proline Bilge Pump - 22102 - 189-22102F1
Features an efficient, water-cooled motor with greater torque and less power consumption; a tough resin housing which resists shock, detergents, fuel and corrosives; a rugged impeller and a quick release bracket. 4 3/8" high. 3-Year warranty.
1000 Chair Comp.W/Ped & Cush. - 705015 - 100-705015F1
Package Includes seat, removable snap-on cushion set, polyethylene mounting plate, 15" anodized aluminum pedestal, bushing and manual slider w/Mounting Plate & Spider.
100 Ft Rl 1-In Black Insert Replaces P/N 117-25212 Rvx - 25212 - 17-25212F1
Replace cracked and stained trim inserts with easy-to-install replacement inserts for aluminum roof edge, trim molding and truck camper shells. (Not designed for windows, entry doors, compartment doors or vents.) UV inhibitors for longer life.
10# Flash Weight - 2295184 - 627-2295184F1
Cannon Trolling Flash Weights™ incorporate a flashing prism design for extra lure power. They are black vinyl coated. The Keel keeps weight tracking accurately and prevents cable twisting.
10" Dock Line Spring - 0759001Znc - 9-0759001Zncf1
Galvanized spring steel10" length overall, 1-1/2" O.D., 4-1/2" compressionFor 1/2" rope size
10' Heavy Duty Sewer Hose Replaces P/N 117-39621 Rvx - 39621 - 17-39621F1
These brown sewer hoses are 15 mils of high tensile strength (HTS™) vinyl, created for the seasonal RVer who makes weekend trips during the summer camping season.
10' Dometic O/B Hose Kit, Pair - Ho5110 - 1-Ho5110F1
Includes two hoses - can be used with all Dometic systems, except SeaStar PRO, BayStar, Capilano and 3-line inboard systems. ID of 5/16".
10' Accutech Zerotorque Feedback Rack Steering System - Accutech10 - 216-Accutech10F1
The patented ZeroTorque Feedback clutch eliminates rudder torque at the steering wheel. A perfect solution for boats without power assist or any boat with moderate rudder torque. This 3.5 turn lock to lock package delivers smooth steering with minimal lost motion.Includes:M86 - preassembled helm with steering cableG88NR® - non-reversible shaft assemblyX34 - 90° bezel
10.04 Dia. Vernalift Mufflertop In/Top Out - 1500010 - 383-1500010F1
Extremely effective in reducing engine exhaust noise and preventing water from returning to the engine. High strength design provides a significant safety margin over other existing fiberglass lift mufflers. Exceeds ABYC specifications. For Gas/Diesel fuel type Inboards, Sailboats & Generator applications. Sound rating: Better. Use above or below the waterline.
10 X11 X1 Epdm Pads 2Pk - Jbp-1011.1 - 375-Jbp10111F1
Stromberg Carlson JBP10111 Base Pads, 10" x 11" x 1", 2/pk
10 Vented Rotr Hubdisc Brk Kit 641-82113 - K71-G00-98 - 641-K71G0098F1
10 Micron Fuel Filter/Water Se - 120R-Rac-02 - 62-120Rrac02F1
Spin-On series filters these filters are designed for high performance applications, and with flow rates between 30 and 120 GPH your engine will perform better than ever with clean, waterfree fuel. These filters are coated with a durable electrostatically applied powder coating for superior corrosion resistance. Features a high capacity Aquabloc® II 10 micron filter element that removes sediment from water up to 99%. This Spin-On filter design is simple to replace and the re-usable clear plastic or metal contaminant collection bowls feature a self-venting drain, or metal plug, for removing unwanted muck and water. Max pressure 7 psi.Clear Bowls: Use for outboard and above deck installations.Metal Bowls: USCG regulations require the use of flame resistant metal bowls below deck.
10 Keel Roller - Rp-10 - 122-Rp10F1
Durable orange polyurethane. Will not mark or discolor boat. Cut and abrasion resistant. Will not "flat spot" even after months of storage. Roller is unaffected by grease, oil, gasoline, exhaust fumes, salt, etc. No bushings to pop out. Continuous bearings and reinforcing tubes on rollers over 7" long are completely enclosed in polyurethane. Shafts should be greased at installation.
10 Floating Winch Handle - Wh1000 - 22-Wh1000F1
Non-corrosive. Perfect low cost alternative. Strong but not intended to replace bronze handles. Reinforced engineering-grade resins and aluminum. Non-magnetic and will not rust. Floats.
1/8 Bronze Pipe Tee - 44250 - 38-44250F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/8 Bronze Pipe Coupling - 44410 - 38-44410F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/8 Bronze Pipe Cap - 44470 - 38-44470F1
Bronze NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/8 Bronze 90 Deg Street Ell - 44160 - 38-44160F1
Bronze 90°, male/female threads. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/8 Brass Sq Head Pipe Plug - 28084 - 38-28084F1
Imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4X1/8 Bronze Reducing Coupling - 44430 - 38-44430F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4In Idx36 Lp Hose/Quick Disc Bell Rv Rvx - 1010039536 - 135-1010039536F1
1/4" X 4' Anchor Lead Chain Yellow - 2115-Y - 238-2115Yf1
Coated, corrosion resistant. Over-sized end links for easy shackle attachment. Grade 30.
1/4" X 4' Anchor Lead Chain White - 2115-W - 238-2115Wf1
Coated, corrosion resistant. Over-sized end links for easy shackle attachment. Grade 30.
1/4" X 4' Anchor Lead Chain Royal Blue - 2115-R - 238-2115Rf1
Coated, corrosion resistant. Over-sized end links for easy shackle attachment. Grade 30.
1/4" X 4' Anchor Lead Chain Red - 2115-Rd - 238-2115Rdf1
Coated, corrosion resistant. Over-sized end links for easy shackle attachment. Grade 30.
1/4" X 4' Anchor Lead Chain Black - 2115-B - 238-2115Bf1
Coated, corrosion resistant. Over-sized end links for easy shackle attachment. Grade 30.
1/4" X 24" X 54" White Starboard - P10-2524Wha54-1 - 236-P102524Wha541F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/4" X 24" X 54" Black Starboard - P10-2524Blk54-1 - 236-P102524Blk541F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/4" X 12" X 6" White Starboard - P10-2506Wha12-1 - 236-P102506Wha121F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/4" X 12" X 27" White Starboard - P10-2512Wha27-1 - 236-P102512Wha271F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/4" X 12" X 12" White Starboard - P10-2512Wha12-1 - 236-P102512Wha121F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/4" X 1/2" Pivot 40 Series - 36361 - 1-036361F1
Pivot for 4300 series cables
1/4" Stainless Steel Bow Shackle, Carded - 147006-1 - 354-1470061F1
Constructed of investment cast 316 stainless the D style shackle has straight sides with a U-shape rounded bottom. Designed for rigging applications with bidirectional loads. The U-shaped end can handle heavy loads, loads on the straight sides, however, may cause bending. We do not load rate cast shackles.
1/4" Stainless Shock Cord Clip W/Crimp, Pair - 657066-1 - 354-6570661F1
Shock Cord Hooks & Crimps can be used with bulk shock cords to create custom tie-down lengths. Corrosion resistant formed 304 stainless steel construction.
1/4" Shut-Off Full Flow Ball Valve - 77-101-10 - 37-7710110F1
Comes with mounting pads. Use where full flow is required. Bronze body. Chromium plated ball. Reinforced TFE seats & stuffing box ring. Blow out stem design. Stainless steel lever and nut. Meets WW-V-35C Type II. BRZ style type. Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" Nylon Shock Cord Clip, White, Pair - 652060-1 - 354-6520601F1
Shock Cord Clips can be used with bulk shock cords to create custom tie-down lengths. UV stabilized injection molded nylon construction.
1/4" Nylon Shock Cord Clip, Black, Bulk - 652061 - 354-652061F1
Shock Cord Clips can be used with bulk shock cords to create custom tie-down lengths. UV stabilized injection molded nylon construction.
1/4" Npt X 3/8" Alum Hose Ba - 033442-10 - 114-03344210F1
Allows customers to customize their fuel line assemblies to match existing connectors on their fuel tanks! All fittings are built to OEM specifications for replacement parts and use o-ring construction for tight, leak-free connections.
1/4" Hose X 3/8 Pipe Male Hose Barb - 32006 - 38-32006F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" Hose X 1/8 Pipe Male Hose Barb - 32004 - 38-32004F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" Hose X 1/4 Pipe Male Hose Barb - 32005 - 38-32005F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" Galvanized Anchor Shackles, 50 Pieces - 147806-5 - 354-1478065F1
Galvanized anchor shackles in a counter top display.
1/4" Cable Clamps, Natural 6 Pcs. - 401251 - 639-401251F1
Marine Grade® Nylon Cable Clamp. Pure nylon for maximum stregth and resistance to solvents, oils, acids and moisture. Unique screw hole alignment feature to speed installation. Absorbs shock and vibration, reduces unwanted noise.
1/4" Bronze 45 Degree Street Elbow - 44-201 - 38-44201F1
1/4" Bronze 45 Degree Street Elbow NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" Brass Hose Splicer - 32093 - 38-32093F1
1/4" Brass Hose Splicer NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" Ball Valve W/ Ss Lever - 70-101-10 - 37-7010110F1
Cast bronze with a stainless steel handle and stem nut. Ball is chrome plated for long lasting corrosion resistance. Reinforced TFE seats and stuffing box ring.Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4" 233+ Paint Masking Tape - 7000048806 - 71-26344F1
Highly conformable tape provides outstanding paint lines.
1/4-20X 2 Ss P/H M/S Phillipsp 100/Bx Pmg - 5114-316 - 828-14X2P13Msf1
1/4 X 3/4 X 8' Hatch Tape - V30-0748B8-2 - 236-V300748B82F1
Medium density closed cell foam with self adhesive for convenient installation. Provides anti-rattle seal.
1/4 X 25' Flex Trim White - V30-1008W25-1 - 236-V301008W251F1
Used to cap any raw edge fiberglass, metal, glass or plexiglas. Easy to install, internal aluminum clips secure trim.
1/4 X 25' Flex Trim Black - V30-1008B25-1 - 236-V301008B251F1
Used to cap any raw edge fiberglass, metal, glass or plexiglas. Easy to install, internal aluminum clips secure trim.
1/4 X 1/8 Bronze Hex Bushing - 28102 - 38-28102F1
Bronze hex head. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4 Quick Disc W/1/4In Ball Va Bell Rv Rvx - 10104052 - 135-10104052F1
1/4 Pt All Purp Cement Clear Bell Rv Rvx - 7530818 - 135-7530818F1
1/4 Plastic Cable Strap 10/B - 0196Dp2 - 9-0196Dp2F1
Black plastic that is ultra-violet stabilized for weather resistance. Eliminates need for insulating cushion. Width is 1/2". Conforms to USCG standards. 10 Per Card.
1/4 In Shackle Anchor Galv Replaces P/N 284-Mc6646G - Mc646G - 284-Mc646Gf1
1/4 Bronze Pipe Tee - 44251 - 38-44251F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4 Bronze Pipe Coupling - 44411 - 38-44411F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4 Bronze Pipe Cap - 44471 - 38-44471F1
Bronze NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4 Bronze 90 Deg Street Ell - 44161 - 38-44161F1
Bronze 90°, male/female threads. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4 Brass Sq Head Pipe Plug - 28085 - 38-28085F1
Imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/4 B Solenoid + Fitting 12V - 130077082Kit - 606-130077082Kitf1
Low pressure brass LPG solenoid shut-off valve. Will not open with high pressure and will close with no or low electric current. Draws 790 mA when in use. CE certified. Comes with 2 brass connection fittings for ease of installation.
1/2X3/8 Bronze Reducing Coupling - 44435 - 38-44435F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2X1/4 Bronze Reducing Coupling - 44434 - 38-44434F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2In Dia. D-Ring For Tie Down Strong & Reliable Ram - Dr-12B - 656-Dr12Bf1
1/2" X 300' 8-Plait Performance Anchor Rode - Hm15Ht300Px - 239-Hm15Ht300Pxf1
8-Plait rode allows you to fit 30% more line in the anchor locker than with standard 3-strand rope rode. Eliminates all kockling and kinking, reducing the risk of jamming in the windlass gypsy and resists stiffening with age.
1/2" X 24" X 54" White Starboar - P10-5024Wha54-1 - 236-P105024Wha541F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/2" X 24" X 54" Black Starboard - P10-5024Blk54-1 - 236-P105024Blk541F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/2" X 24" X 27" White Starboard - P10-5024Wha27-1 - 236-P105024Wha271F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/2" X 24" X 27" Black Starboard - P10-5024Blk27-1 - 236-P105024Blk271F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/2" X 200' Long Link Self-Colored Mooring Chain, Drum - 8611647 - 251-8611647F1
A low carbon steel, general purpose chain with a versatile long link design. The long link makes it more flexible and ideally suited for mooring applications. 40% stronger than Acco's original chain products. The long link construction allows the hook-up of shackles anywhere on the chain, not just on the end links.
1/2" X 200' Long Link Galvanized Mooring Chain, Drum - 500140850 - 251-500140850F1
A low carbon steel, general purpose chain with a versatile long link design. The long link makes it more flexible and ideally suited for mooring applications. 40% stronger than Acco's original chain products. The long link construction allows the hook-up of shackles anywhere on the chain, not just on the end links. Chain is continuously hot-dipped galvanized to provide a deep, strong protective coating.
1/2" X 200' 8-Plait Performance Anchor Rode - Hm10Ht200Px - 239-Hm10Ht200Pxf1
8-Plait rode allows you to fit 30% more line in the anchor locker than with standard 3-strand rope rode. Eliminates all kockling and kinking, reducing the risk of jamming in the windlass gypsy and resists stiffening with age.
1/2" X 12" X 27" White Starboarde - P10-5012Wha27-1 - 236-P105012Wha271F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/2" X 12" X 27" Black Starboard - P10-5012Blk27-1 - 236-P105012Blk271F1
UV-Stabilized marine grade polymer. UV resistant. Withstands extreme weather conditions. Will not rot, delaminate, swell or splinter. The matte texture requires no painting, finishing, or maintenance. It will last the lifetime of your boat. Pre-cut and packaged with do-it-yourself project ideas. Easy to work with using standard woodworking tools. 1 Year warranty.
1/2" White Plastic Thru-Hull W/Broad Flange - 50-18011 - 50-18011F1
Molded plastic with broad flange. Per ABYC "Safety Standards for Small Craft". Not recommended for use below the waterline.
1/2" Stainless Steel Bow Shackle, Carded - 147012-1 - 354-1470121F1
Constructed of investment cast 316 stainless the D style shackle has straight sides with a U-shape rounded bottom. Designed for rigging applications with bidirectional loads. The U-shaped end can handle heavy loads, loads on the straight sides, however, may cause bending. We do not load rate cast shackles.
1/2" Shut-Off Full Flow Ball Valve - 77-103-10 - 37-7710310F1
Comes with mounting pads. Use where full flow is required. Bronze body. Chromium plated ball. Reinforced TFE seats & stuffing box ring. Blow out stem design. Stainless steel lever and nut. Meets WW-V-35C Type II. BRZ style type. Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Shaft Anode, Zinc - Cmx00 - 194-Cmx00F1
Streamlined Shaft Anodes w/Allen Screw
1/2" Scoop Thru Hull W/Nut - 0065Dp4Plb - 9-0065Dp4Plbf1
Cast bronze. Screw size is #8. Strainer is 3" x 4", except for 65DP7PLB which is 3-1/4" x 4-1/4". Includes nut. UL Listed. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Metal Buckles (100/Bag) - Pacb412 - 315-Pacb412F1
For use with strapping and tensioning tool.
1/2" Intake Water Strainer - 0493004Plb - 9-0493004Plbf1
Cast bronze. Designed for easy installation and cleaning. Features mounting lugs cast into both sides to assure universal mounting, four outside tie rods and a 316 stainless steel strainer basket to minimize electrolysis. Hinged lugs for cast bronze cover permit easy removal and cleaning of basket. Drain plug in bottom casting is provided for easy removal of sediment and draining for winterization. Ratio given for open area to pipe size.
1/2" Hose X 3/8 Pipe Male Hose Barb - 32016 - 38-32016F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Hose X 3/4 Pipe Male Hose Barb - 32018 - 38-32018F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Hose X 1/4 Pipe Male Hose Barb - 32015 - 38-32015F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Hose X 1/2 Pipe Male Hose Barb - 32017 - 38-32017F1
Temperature and working pressure ranges - From -400F to +1600F at 150 PSI maximum. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Full Flow Ball Valve, Low Profile - 00Bbv50Lp - 379-00Bbv50Lpf1
Bronze, full flow drain & grounding screw. Hard chrome bronze ball and vinyl coated stainless steel handle.
1/2" Bronze 45 Degree Street Elbow - 44203 - 38-44203F1
1/2" Bronze 45 Degree Street Elbow NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Brass Hose Splicer - 32096 - 38-32096F1
1/2" Brass Hose Splicer NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" Ball Valve W/ Ss Lever - 70-103-10 - 37-7010310F1
Cast bronze with a stainless steel handle and stem nut. Ball is chrome plated for long lasting corrosion resistance. Reinforced TFE seats and stuffing box ring.Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" 3-Way Bronze Diverter Valve - 70-603-10 - 37-7060310F1
Features a chrome plated ball, reinforced TFE seats, stuffing box ring, and adjustable packing gland. Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2" 233+ Paint Masking Tape - 26332 - 71-26332F1
Highly conformable tape provides outstanding paint lines.
1/2 X200'Nylon W/1/4 X 15' - 69000334 - 239-69000334F1
Designed specifically for top performance with all Lewmar V series and Pro series windlasses. They feature ACCO hi-test, hot-dipped galvanized chain and 3-strand nylon twist rope that is chemically treated to remain flexible after constant exposure to salt water and sun. A special tapered splice allows smooth transition from rope to chain
1/2 X 3900' Strap Cross Woven - Pd50Tcw - 315-Pd50Tcwf1
Used with uprights and buckles to form the support structure under shrinkwrap covers.
1/2 X 3/8 Bronze Hex Bushing - 44505 - 38-44505F1
Bronze hex head. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 X 3 1/2 Brass Pipe Nipple - 40-065 - 38-40065F1
Nipple Brass 1/2 X 3 1/2 NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 X 1500' Strap-Cross Woven - Pd40Tcw - 315-Pd40Tcwf1
Used with uprights and buckles to form the support structure under shrinkwrap covers.
1/2 X 150' Nylon W/1/4 X 10' - 69000332 - 239-69000332F1
Designed specifically for top performance with all Lewmar V series and Pro series windlasses. They feature ACCO hi-test, hot-dipped galvanized chain and 3-strand nylon twist rope that is chemically treated to remain flexible after constant exposure to salt water and sun. A special tapered splice allows smooth transition from rope to chain
1/2 X 1/8 Bronze Hex Bushing - 44503 - 38-44503F1
Bronze hex head. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 X 1/4 Bronze Hex Bushing - 44504 - 38-44504F1
Bronze hex head. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 Thru Hull Connection - 0328Dp4 - 9-0328Dp4F1
Molded white plastic with broad flange. For use with hose. Not recommended for use below waterline.
1/2 Plastic Cable Strap 10/B - 0196Dp5 - 9-0196Dp5F1
Black plastic that is ultra-violet stabilized for weather resistance. Eliminates need for insulating cushion. Width is 1/2". Conforms to USCG standards. 10 Per Card.
1/2 Pipe To Hose Adapter - 0076Dp4Plb - 9-0076Dp4Plbf1
Cast bronze. Meets requirements of USCG safety standards.
1/2 In Shackle Anchor Galv Replaces P/N 284-Mc6650G - Mc650G - 284-Mc650Gf1
1/2 Glue Brushes (144/Box) - 803-144 - 655-803144F1
A handy disposable brush with a 6" metal handle. Used for a wide variety of gluing and coating.
1/2 Glue Brushes (12/Pk) - 803-12 - 655-80312F1
A handy disposable brush with a 6" metal handle. Used for a wide variety of gluing and coating.
1/2 Facepiece, Ultimate Reusable, Med. - 37082 - 71-37082F1
Advance silicone material for increased comfort and greater durability Proprietary 3M™ CoolFlow™ valve helps makes breathing easierDual-mode head harness adjusts easily for either standard or drop-down modeExhalation valve cover directs exhaled breath and moisture downward to reduce fogging
1/2 Facepiece, Ultimate Reusable, Lg. - 7100134949 - 71-7503F1
Advance silicone material for increased comfort and greater durability Proprietary 3M™ CoolFlow™ valve helps makes breathing easierDual-mode head harness adjusts easily for either standard or drop-down modeExhalation valve cover directs exhaled breath and moisture downward to reduce fogging
1/2 Facepiece, Ultimate Reusable, Lg. - 37083 - 71-37083F1
Advance silicone material for increased comfort and greater durability Proprietary 3M™ CoolFlow™ valve helps makes breathing easierDual-mode head harness adjusts easily for either standard or drop-down modeExhalation valve cover directs exhaled breath and moisture downward to reduce fogging
1/2 Bronze Pipe Tee - 44253 - 38-44253F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 Bronze Pipe Coupling - 44413 - 38-44413F1
Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 Bronze Pipe Cap - 44473 - 38-44473F1
Bronze NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 Bronze 90 Deg Street Ell - 44163 - 38-44163F1
Bronze 90°, male/female threads. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 Brass Sq Head Pipe Plug - 28087 - 38-28087F1
Imported. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1/2 Black Grommets (5) - 760500 - 639-760500F1
Flexible Black VinylProvides instant abrasion resistance to wires passing through panel holes.
1"Bronze Seacock W/Straight Tail Piece - 0835006Plb - 9-0835006Plbf1
Includes: thru-hull, hose adapter, drain plug, four pre-drilled mounting holes and bonding screw. Incorporates a plastic ball and seat assuring a tight seal and ease of operation and drain plugs for winterizing. Handles are easily removed. Overall height is measured from the top of the hose adapter to the bottom of the flange.
1" Yachtsman Brush - Z112010 - 391-Z112010F1
White China bristle brush, chisel construction, produces a smooth finish with alkyd and oil-based varnishes, marine paints, stains, and urethanes. Round brass-plated steel ferrule; black solid plastic handle.
1" X50Yd Utility Cloth P80 - 5111519792 - 71-19792F1
314DAn aluminum oxide abrasive product sheet. 1" wide constructed on a J weight, durable cloth backing. Primary market: metalworking.
1" X50Yd Utility Cloth P400 - 5111519783 - 71-19783F1
314DAn aluminum oxide abrasive product sheet. 1" wide constructed on a J weight, durable cloth backing. Primary market: metalworking.
1" X50Yd Utility Cloth P320 - 5111519784 - 71-19784F1
314DAn aluminum oxide abrasive product sheet. 1" wide constructed on a J weight, durable cloth backing. Primary market: metalworking.
1" X50Yd Utility Cloth P150 - 5111519789 - 71-19789F1
314DAn aluminum oxide abrasive product sheet. 1" wide constructed on a J weight, durable cloth backing. Primary market: metalworking.
1" X 60' Gray Med. Duty Safety Walk - 7000051950 - 71-Sw1Grf1
Medium DutyAnti-slip tape offers excellent traction enhancement. Used around barefoot or deckshoe areas such as trailers, decks, docks, ladders, stairs and cockpits
1" X 60' Black Heavy Duty Safety Walk - 7100029620 - 71-Sw1F1
Heavy Duty - Anti-slip tape has a diamond hard mineral surface for extra traction. It is designed for use around areas of heavy traffic.
1" Thru-Hull With Nut - Th-100-W - 34-Th100Wf1
Should have threaded portion cut to proper length considering hull and butt block thickness. Consider thread depth when using a seacock. Sealant is recommended between hull and thru-hull flange. Includes nut.NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Strainer 304 Ss Basket - Arg-1000-S Bspp - 34-Arg1000Sbsppf1
Standard single strainers. No tie rods or leaks under pressure or vacuum. Quick and easy mounting system allowing removal of strainer without tools. #304 Stainless steel filter basket. O-ring seals at strainer cap and between strainer head and sight glass. See-thru screw-on strainer cap allows easy, no-tools maintenance. Spanner wrench holes in cover allow the use of SW-2531 wrench. Install with pipe or hose. Do not use chemical or abrasive cleaners on sight glass. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Shut-Off Full Flow Ball Valve - 77-105-10 - 37-7710510F1
Comes with mounting pads. Use where full flow is required. Bronze body. Chromium plated ball. Reinforced TFE seats & stuffing box ring. Blow out stem design. Stainless steel lever and nut. Meets WW-V-35C Type II. BRZ style type. Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Shaft Anode, Zinc - Cmx03 - 194-Cmx03F1
Streamlined Shaft Anodes w/Allen Screw
1" Scoop Thru-Hull W/Nut - Sth-100-W - 34-Sth100Wf1
Includes locking nut. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Scoop Thru Hull W/Nut - 0065Dp6Plb - 9-0065Dp6Plbf1
Cast bronze. Screw size is #8. Strainer is 3" x 4", except for 65DP7PLB which is 3-1/4" x 4-1/4". Includes nut. UL Listed. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" S.S. Tubing - S14-1049P6-1 - 236-S141049P61F1
Type-304 marine-grade steel, polished and buffed.
1" S.S. Tubing - S14-1049P12 - 236-S141049P12F1
Type-304 marine-grade steel, polished and buffed.
1" Onyx Brush - 12013 - 321-12013F1
A better quality with chisel trim, painted foam black handle and 100% white china bristle.
1" Intake Water Strainer - 0493006Plb - 9-0493006Plbf1
Cast bronze. Designed for easy installation and cleaning. Features mounting lugs cast into both sides to assure universal mounting, four outside tie rods and a 316 stainless steel strainer basket to minimize electrolysis. Hinged lugs for cast bronze cover permit easy removal and cleaning of basket. Drain plug in bottom casting is provided for easy removal of sediment and draining for winterization. Ratio given for open area to pipe size.
1" Heritage Badger Brush - 16055-1 - 130-160551F1
Soft badger-style brush. Pure China bristle. Unlacquered hardwood peg handle. Epoxy set in stainless steel ferrule. Hand formed chisel to preserve natural soft flagg tips. Extra fine tip. Excellent tipping off brush for Awl-Grip. Made in USA.
1" Full Flow Ball Valve, Low Profile - 00Bbv100Lp - 379-00Bbv100Lpf1
Bronze, full flow drain & grounding screw. Hard chrome bronze ball and vinyl coated stainless steel handle.
1" Fooler Brush @ 36 - 10001 - 321-10001F1
100% natural bristle. Double the thickness and holds more coating of a typical chip brush. Square trim, wood handle. Recommended for epoxy and polyester resins, bottom paint, industrial coating, but not for fine finishes.Sold in Full Boxes Only.
1" Bronze Seacock W/90° Tail Piece - 0834006Plb - 9-0834006Plbf1
Includes: thru-hull, hose adapter, drain plug, four pre-drilled mounting holes and bonding screw. Incorporates a plastic ball and seat assuring a tight seal and ease of operation and drain plugs for winterizing. Handles are easily removed. Overall height is measured from the top of the hose adapter to the bottom of the flange. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Bronze Seacock Body - 0805006Plb - 9-0805006Plbf1
Ball valve design. Cast bronze. Meets needs of applications that require long, scoop or flush type thru-hulls.
1" Bronze Full Flow In-Line Ball Valve - Ibv-1000 Bspp - 34-Ibv1000Bsppf1
Patented field reversible handle allows you to select the closed position orientation (clockwise or counterclockwise) that best suits the installation. Handle has square hole to accept standard ratchet, to help reach valves in hard-to-reach locations and ease actuation of difficult to operate valves. 400 WOG rated. Stainless steel handle and hardware. Chrome plated solid brass ball (not a hollow ball). PTFE seats and seals. UL Listed for fuel or water.NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Bronze 45 Degree Street Elbow - 44205 - 38-44205F1
1" Bronze 45 Degree Street Elbow NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Ball Valve W/ Ss Lever - 70-105-10 - 37-7010510F1
Cast bronze with a stainless steel handle and stem nut. Ball is chrome plated for long lasting corrosion resistance. Reinforced TFE seats and stuffing box ring.Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" Badger Brush - 10011 - 321-10011F1
Premium quality. Hand formed chisel edge. Cup chisel trim, natural stock and pencil style, clear wood handle.
1" Ace Brush - 12011 - 321-12011F1
Good quality brushes. Square trim, solid black plastic handle and 100% Black China bristle.
1" 3-Way Bronze Diverter Valve - 70-605-10 - 37-7060510F1
Features a chrome plated ball, reinforced TFE seats, stuffing box ring, and adjustable packing gland. Made in U.S.A. NOT TO BE USED IN POTABLE WATER SYSTEMS.
1" 233+ Paint Masking Tape - 26336 - 71-26336F1
Highly conformable tape provides outstanding paint lines.
1" & 1-1/8" Inline Non-Return Valve - Lv1218 - 698-Lv1218F1
Simple way to maintain prime in a suction or discharge line. Designed to fit in-line. Use with manual or electric pumps.
1" & 1-1/2" Inline Non-Return Valve - Lv1215 - 698-Lv1215F1
Simple way to maintain prime in a suction or discharge line. Designed to fit in-line. Use with manual or electric pumps.
1.77" Snap-Lock™ Seat Mount, Bulk - 19000 - 148-19000F1
Snaps into posts and locks for added securityE-coated for superior corrosion-resistance3° Tilt
1.77" Snap-Lock™ Adjustable Power Pedestal - 39204 - 148-39204F1
Integral seat mount1.77" diameter postClear anodized aluminum finish
1.5" Onyx Brush - 12023 - 321-12023F1
A better quality with chisel trim, painted foam black handle and 100% white china bristle.
1.5" Fooler Brush @36 - 10015 - 321-10015F1
100% natural bristle. Double the thickness and holds more coating of a typical chip brush. Square trim, wood handle. Recommended for epoxy and polyester resins, bottom paint, industrial coating, but not for fine finishes.Sold in Full Boxes Only.
1.5" Ball Quick Release Kayak Track Base - Rap-383U - 170-Rap383Uf1
For the serious kayak angler, the RAM Quick Release Track Base is a universal mounting solution for a wide variety of kayak products including RAM fishing rod holders, camera and transducer deployment arms. Designed to accommodate all kayak tracks, as well as common track systems, engage and fasten the base to your existing track system or many other's including GearTrac, SlideTrax and the common T-Track. With a quick turn of the ball the base will slide along the track, giving you ultimate flexibility in repositioning your rod holder. A necessity for all fishing enthusiasts, the RAM Quick Release Track Base is certain to create more mounting options on whatever you choose to take to the water. Track Dimensional Range: .250" MIN. - .562" MAX. High strength composite. Quick release and installationEasily relocate adapter along track, can be installed at any point on the trackHigh strength materials ensure product longevityCompatible with RAM-ROD™ holders with 1.5" ball and any 1.5" RAM accessoryLifetime warranty
1.5" Badger Brush - 10021 - 321-10021F1
Premium quality. Hand formed chisel edge. Cup chisel trim, natural stock and pencil style, clear wood handle.
1.5" Ace Brush - 12021 - 321-12021F1
Good quality brushes. Square trim, solid black plastic handle and 100% Black China bristle.
1.5 Mil Clear Plastic Sheeting - Cf01520200C - 28-Cf01520200Cf1
Use for paint protection, vapor barrier, moisture barrier and insulation.
1.5 Mil Clear Plastic Sheeting - Cf01512200C - 28-Cf01512200Cf1
Use for paint protection, vapor barrier, moisture barrier and insulation.
1-3/8 X 1-7/8 X 5-1/2 Brass Cutless Bearing - Devilfish - 87-Devilfishf1
Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII. Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing. Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi. Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity
1-3/8 Bearings Bulk Pk/10 - 81160 - 641-81160F1
Sized to fit all popular trailers.
1-1/8" White Plastic Thru-Hull W/Broad Flange - 18090 - 50-18090F1
Molded plastic with broad flange. Per ABYC "Safety Standards for Small Craft". Not recommended for use below the waterline.
1-1/8" Shaft Anode, Zinc - Cmx04 - 194-Cmx04F1
Streamlined Shaft Anodes w/Allen Screw
1-1/8 Thru Hull Connect Bulk - 0328Dp6A - 9-0328Dp6Af1
Molded white plastic with broad flange. For use with hose. Not recommended for use below waterline.
1-1/8 Striker Base Flush Mt. - F16-0212-F - 236-F160212Ff1
Features 12 locking positions with hex nut design. Made with Type-316L Stainless Steel. Will fit both port and starboard bases. Welded locking adapter for maximum strength. Removable arms for unobstructed decks. Fits 12' & 15' standard tele-outriggers. 45° gunnel mount base. 3 Year warranty.
1-1/8 Chr Thru-Hull F/Hose - 035006Adpc - 9-035006Adpcf1
Available in plain or chrome plated bronze, these fittings have a hose barb connection and are recommended for use above the waterline only. The flange is machined to fit the hull tightly and grooved to retain bedding compound. Minimum hull thickness 3/8".
1-1/4X6 Ss Piano Hinge Polish. - H14-0114P72 - 236-H140114P72F1
Type-304 Stainless Steel, .040 gauge. Holes are drilled on 2" centers with no stagger. Great for doors, large cabinets and hatches. Available in 6' lengths only. NOTE: A UPS/FedEx overlength/packaging fee may apply to this product.
