Jabsco
Water Puppy Pump, 12V - 18660-0121 - 6-186600121F1
This bronze body, self-priming impeller pump will produce a dry prime suction lift of about 4' and has a maximum head of 20'. Use for bilge pumping, livewell circulation, washdown, and general pumping applications. Cannot be run dry. Permanent magnet type motor is fully enclosed with a stainless steel shaft and complies with USCG Electrical Standards 183.410 and ISO 8846 marine for ignition protection on gasoline powered vessels. If the water contains a significant amount of oil use oil resistant nitrile impeller #6303-0003. Ports: 1/2" internal pipe threads, 1" external hose barb & 3/4" external garden hose adapter. NOT TO BE USED IN POTABLE WATER SYSTEMS.
Vented Loop 3/4" W/Check Valve - 29015-0000 - 6-290150000F1
An essential accessory to prevent water from siphoning into toilets that are installed below a vessel's waterline.
Ultra Max Water Pressure Set - 59451-1012 - 6-594511012F1
This fully assembled pressure set includes a pump, strainer and pre-pressurized accumulator tank rubber mounted on a board. Serves 3 or more 1/2" outlets, is self-priming up to 10' and is suitable for vertical or horizontal installation. Quadruple diaphragm design for smooth, quiet operation is also capable of extended dry running. Motor is thermal overload protected and complies with USCG 183.410 and ISO 8846 marine ignition protection. Includes 1/2" hose barb and 1/2" QEST fittings. 15 1/2" L x 15 3/4" W x 5 1/2" H.
Type Iii Msd Waste Management System - 38110-0092 - 6-381100092F1
Provides an easy-to-install, all-inclusive solution consisting of a compact polyethylene holding tank and an integral Run-Dry Macerator Pump. The system has a touch-pad control panel to monitor waste levels and when required the user can activate the macerator pump to evacuate waste.
Solenoid Valve For Electric Toilets - 37068-2000 - 6-370682000F1
Should be used where 37010 series electric toilets are installed below the waterline line to ensure maximum electric toilet performance and primeability when installing a vented loop in the inlet hose. Install a loop on the inlet plumbing rising at least 8" above the highest waterline level, and installing a vented loop fitting at the top of the loop to stop water siphoning over the loop and flooding the vessel. Solenoid valve attaches directly to Jabsco vented loops and is wired to the toilet's on/off switch. It closes whenever the toilet pump is operated and ensures full pump priming. Use with ITT 290150000 vented loop
Small Impeller Puller - 50070-0040 - 6-500700040F1
This tool is the easiest way to remove impellers, especially when the pump is mounted in tight, cramped conditions. It removes the risk of expensive damage to the pump or housing and is manufactured from corrosion resistant cast aluminum and stainless steel.
Shower Drain/Bilge Diaphragm Pump, 4.2 Gpm - 50880-1000 - 6-508801000F1
This robust, single diaphragm pump features no filter requirement and a compact design. The pump head and ports rotate for flexible installation. Self-priming to 10' and can run dry. Meets ISO 8846 and USCG regulations for ignition protection.
Service/Conversion Kit - 18598-1000 - 6-185981000F1
185981000 fits 18590-, 18690-, & 18690- series macerators.
Replacement Nitrile Impeller And Shaft - 17255-0003-P - 6-172550003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 920-0003-P - 6-9200003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 836-0003-P - 6-8360003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 7273-0003-P - 6-72730003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 6760-0003-P - 6-67600003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 6303-0003-P - 6-63030003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 6056-0003-P - 6-60560003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 5929-0003-P - 6-59290003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 4528-0003-P - 6-45280003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 18673-0003-P - 6-186730003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 14750-0003-P - 6-147500003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 1414-0003-P - 6-14140003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Nitrile Impeller - 1210-0003-P - 6-12100003Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 920-0001-P - 6-9200001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 836-0001-P - 6-8360001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 7273-0001-P - 6-72730001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 6303-0001-P - 6-63030001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 4598-0001-P - 6-45980001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 4568-0001-P - 6-45680001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 4528-0001-P - 6-45280001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 31130-0061-P - 6-311300061Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 3085-0001-P - 6-30850001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 22799-0001-P - 6-227990001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 22405-0001-P - 6-224050001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 18958-0001-P - 6-189580001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 18948-0001-P - 6-189480001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 18838-0001-P - 6-188380001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 18673-0001-P - 6-186730001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 17954-0001-P - 6-179540001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 17937-0001-P - 6-179370001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 17936-0001-P - 6-179360001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 17935-0001-P - 6-179350001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 17370-0001-P - 6-173700001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 17018-0001-P - 6-170180001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 14750-0001 - 6-147500001F1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 13554-0001-P - 6-135540001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 1210-0001-P - 6-12100001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Neoprene Impeller - 11979-0001-P - 6-119790001Pf1
See Jabsco Impeller Cross Reference and Impeller Identification Guide for impeller silhouettes and drive types.
Replacement Engine Cooling Pump - 50410-1201 - 6-504101201F1
Flange Mount 1-1/4" PumpBronze bodyNeoprene impeller316 stainless steel shaftBuna 'N' Lip sealSingle row, ball type bearings1-1/4" hose barb ports
Pump-Bronze Seawater Repl - 43210-0001 - 6-432100001F1
Replacement for stock cast-iron, plastic and aluminum composite water pumps. Made of bronze and stainless steel. Withstands harsh, corrosive marine environments. Left or Right hand rotation. One piece bronze body. Bronze end plate. Replaceable cam and wearplate. Pulley driven. Takes impeller 179540001P.
Pump Mini Puppy 12V 1.6Gpm - 18620-0003 - 6-186200003F1
Includes an integral on/off/reversing switch to change direction of flow. Use for circulating and draining bait tanks, changing engine oil, or general pumping. Ports are 3/8" NPT internal and GHT external. Impeller is 14500003. NOT TO BE USED IN POTABLE WATER SYSTEMS.
Pump 12V-Com-Duty Water Puppy - 18670-0123 - 6-186700123F1
This bronze body, self-priming impeller pump will produce a dry prime suction lift of about 6' and has a maximum head of 20'. Use for bilge pumping, livewell circulation, washdown, and general pumping applications. Cannot be run dry. Permanent magnet type motor is fully enclosed with a stainless steel shaft and has adequate torque to reverse the pump. Complies with USCG Electrical Standards 183.410 and ISO 8846 marine for ignition protection on gasoline powered vessels. Ports: 1/2" internal pipe threads, 1" external hose barb & 3/4" external garden hose adapter.
Pump 115Vac 9.5 Gpm - 11810-0003 - 6-118100003F1
This portable, self-priming pump features a bronze pump head, continuous duty 1/3hp motor with thermal over-load protection, and more. Suitable for bait tank circulation, oil transfer, washdown, and utility dock pump. Dry self-priming up to 7.8' with a maximum head of 40'. 8' power cord and convenient handle. Includes nitrile oil resistant impeller. NOT TO BE USED IN POTABLE WATER SYSTEMS.
Pump 115 Volt Water Puppy - 12210-0001 - 6-122100001F1
This portable, self-priming pump features a bronze pump head. Handles hard and soft solids without clogging. Suitable for washing down decks and docks, water for ship's service supply, or pumping out crankcase oil. Dry self-priming up to 4.9' with a maximum head of 40'. Replaceable brushes, 6' power cord and nitrile oil resistant impeller. Includes garden hose thread adapter. NOT TO BE USED IN POTABLE WATER SYSTEMS.
Pulley Driven Flexible Impeller Pump - 7420-1001 - 6-74201001F1
Mid-size pump with vertical oriented ports. Self-priming to 10 ft vertical liftFull thickness cam, mechanical seal, short stainless steel shaftNeoprene impeller,Marine engine cooling for engine models: caterpillar 3160. caterpillar 3208.
Pulley Driven Engine Cooling Pump W/Nitrile Impeller - 777-9003 - 6-7779003F1
Flexible impeller pumps are self-priming to 10' and are ideal for engine cooling, wash-down, circulation, and many general purpose on-board or dockside applications. The bronze bodies and stainless steel shafts are suited for the marine environment and can operate in either rotational direction. Different port orientations available to meet various pumping requirements. Most models have replaceable cams and wearplates for extended life.
Pulley Driven Engine Cooling Pump W/Neoprene Impeller - 777-9001 - 6-7779001F1
Flexible impeller pumps are self-priming to 10' and are ideal for engine cooling, wash-down, circulation, and many general purpose on-board or dockside applications. The bronze bodies and stainless steel shafts are suited for the marine environment and can operate in either rotational direction. Different port orientations available to meet various pumping requirements. Most models have replaceable cams and wearplates for extended life.
Pulley Driven Engine Cooling Pump - 2620-1101 - 6-26201101F1
Self priming flexible impeller pump. Ideal for engine cooling, washdown, circulation and other general purposes. Corrosion resistant bronze bodies and stainless shafts are well suited for marine environments. Permanently lubricated ball bearings.
Par Service Kit - 37182-0000 - 6-371820000F1
Please call our Sales Department for complete ITT spare parts stock and information.SPARE PARTS that are stock items are listed below for Jabsco bilge pumps.
Par Service Kit - 30124-0000 - 6-301240000F1
Please call our Sales Department for complete ITT spare parts stock and information.SPARE PARTS that are stock items are listed below for Jabsco bilge pumps.
Par Service Kit - 30101-0000 - 6-301010000F1
Please call our Sales Department for complete ITT spare parts stock and information.SPARE PARTS that are stock items are listed below for Jabsco bilge pumps.
Par 24V Blower Flangemount 4 - 35400-0010 - 6-354000010F1
Offers safe, efficient and have high volume evacuation of hazardous vapors on vessels equipped with gasoline powered engines. Satisfy requirements of USCG regulation Title 46, Chapter I, part 183, subpart K for marine ventilation when properly installed and used. BIA type accepted. Also exhausts warm air from galleys and engine rooms, ventilating steam or odors from heads and general marine air circulation. Constructed of tough reinforced plastic housing and one-piece balanced rotor for maximum corrosion resistance. Flangemount blowers are generally mounted with discharge port fastened directly to flat external surface minimizing required ducting. Inlet port can be connected with duct hose to area requiring ventilation.
Par 12V Toilet Conversion Kit - 37010-0092 - 6-370100092F1
Converts manual toilet to simple pushbutton electric operation without the need to alter existing inlet or discharge seacocks. Comprehensive kit has all necessary parts, including flushing pump, macerator pump, switch, adapters, clamps, hose and fastenings.
Par 12V Conversion Kit 25Amp - 29200-0120 - 6-292000120F1
Easily converts all PAR manually operated toilets to convenient electric operation. Complete for 29090/2910 series. Existing discharge plumbing remains undisturbed for ease of installation. Inlet port fits 3/4" hose. 10 to 12" high, 4" wide, 7-3/4" deep. Fuse size 25. 24 amp draw.
Par 12V Blower Flangemount - 34739-0010 - 6-347390010F1
Offers safe, efficient and have high volume evacuation of hazardous vapors on vessels equipped with gasoline powered engines. Satisfy requirements of USCG regulation Title 46, Chapter I, part 183, subpart K for marine ventilation when properly installed and used. BIA type accepted. Also exhausts warm air from galleys and engine rooms, ventilating steam or odors from heads and general marine air circulation. Constructed of tough reinforced plastic housing and one-piece balanced rotor for maximum corrosion resistance. Flangemount blowers are generally mounted with discharge port fastened directly to flat external surface minimizing required ducting. Inlet port can be connected with duct hose to area requiring ventilation.
Par 12V 3 Blower Flexmount - 36740-0000 - 6-367400000F1
Offers safe, efficient and have high volume evacuation of hazardous vapors on vessels equipped with gasoline powered engines. Satisfy requirements of USCG regulation Title 46, Chapter I, part 183, subpart K for marine ventilation when properly installed and used. BIA type accepted. Also exhausts warm air from galleys and engine rooms, ventilating steam or odors from heads and general marine air circulation. Constructed of tough reinforced plastic housing and one-piece balanced rotor for maximum corrosion resistance. Flexmount blowers have both inlet and outlet ports designed for slip-on flexible duct connections and are ideal when an in-line installation of blower is preferred. May be rotated in bracket to permit installation with discharge port in any direction.
Mini Accumulator Tank - 30573-0003 - 6-305730003F1
Tank is intended for installation in any pumped water system controlled by a pressure switch and can serve as a storage vessel as well as a pulsation dampener. By smoothing water flow and reducing on/off switch cycling of the pump the result is quieter operation and longer pump life. The even flow of water gives better control of hot water temperature with systems using instant water heaters. Easily fitted to new or existing systems with quick connect fittings. Mounting point for optional pressure switch. Internal bladder. Manufactured from food grade materials, NSF Standard 18 listed.
Mag Drive Centrifugal Pump - 436977 - 6-436977F1
Designed for applications that require a safe and leak free, continuous duty pump. Great for marine air conditioning circulation, ice makers, hot water circulation, livewell and bait tank installations. Pump head is manufactured in chemical resistant thermoplastics - entirely non-metallic. UL listed, ignition and thermally protected fan cooled motor.
Large Impeller Puller - 50070-0200 - 6-500700200F1
This tool is the easiest way to remove impellers, especially when the pump is mounted in tight, cramped conditions. It removes the risk of expensive damage to the pump or housing and is manufactured from corrosion resistant cast aluminum and stainless steel.
Jabsco Vented Loop & Check Valve - 29015-0020 - 6-290150020F1
An essential accessory to prevent water from siphoning into toilets that are installed below a vessel's waterline.
Jabsco Vented Loop & Check Valve - 29015-0010 - 6-290150010F1
An essential accessory to prevent water from siphoning into toilets that are installed below a vessel's waterline.
Jabsco V50Aj115N3A Sensor-Max Ii Variable Speed Freshwater Pump, 5Gpm - V50Aj-115N-3A - 6-V50Aj115N3Af1
The Sensor-Max II incorporates a high performance five chamber design with advanced pressure sensor and variable speed programming that automatically adjusts the motor speed to deliver the right flow and pressure the water system requires. Quiet operation with no water hammerEliminates need for accumulator tankHigh flow capacity, supplies up to five outletsConserves power by adjusting motor speed as neededRobust co-molded diaphragm and cast aluminum lower housing
Jabsco Replacement Impeller For Pcm®/Crusader Raw Water Pump - 50461-1001-P - 6-504611001Pf1
Replacement Impeller.
Jabsco Q402J118N3A Hotshot™ Series Washdown Pump, 24V, 4Gpm - Q402J-118N-3A - 6-Q402J118N3Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetIncludes: 2 x 1/2" Straight Hose barb, 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT Adapter HotShotHD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures
Jabsco Q402J115S3A Par-Max Heavy Duty Water System Pump, 24V, 4Gpm - Q402J-115S-3A - 6-Q402J115S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco Q401J118S3A Par-Max Heavy Duty Water System Pump, 12V, 4Gpm - Q401J-118S-3A - 6-Q401J118S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco Q401J118N4A Hotshot™ Series Washdown Pump Kit W/Hose, 12V, 4Gpm - Q401J-118N-4A - 6-Q401J118N4Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetIncludes: 2 x 1/2" Straight Hose barb, 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT Adapter HotShotHD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressuresFull kit version include 25' (7.6m) hose coil
Jabsco Q401J118N3A Hotshot™ Series Washdown Pump, 12V, 4Gpm - Q401J-118N-3A - 6-Q401J118N3Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetIncludes: 2 x 1/2" Straight Hose barb, 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT Adapter HotShotHD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures
Jabsco Q401J115S3A Par-Max Heavy Duty Water System Pump, 12V, 4Gpm - Q401J-115S-3A - 6-Q401J115S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco Q301J118S3A Par-Max Heavy Duty Water System Pump, 12V, 3Gpm - Q301J-118S-3A - 6-Q301J118S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco Q301J115S3A Par-Max Heavy Duty Water System Pump, 12V, 3Gpm - Q301J-115S-3A - 6-Q301J115S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco Pumpgard In-Line Strainer - 36400-1000 - 6-364001000F1
Prevents dirt and other particles from entering pump intake. Cuts down on repairs. Transparent housing for quick inspection, 50 mesh stainless steel filtering screen.
Jabsco Pumpgard In-Line Strainer - 36200-1000 - 6-362001000F1
Prevents dirt and other particles from entering pump intake. Cuts down on repairs. Transparent housing for quick inspection, 50 mesh stainless steel filtering screen.
Jabsco P602J219N3A Hotshot™ Series Washdown Pump, 24V, 6Gpm - P602J-219N-3A - 6-P602J219N3Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetIncludes: 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT AdapterHD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures
Jabsco P602J215S3A Par-Max Heavy Duty Water System Pump, 24V, 6Gpm - P602J-215S-3A - 6-P602J215S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco P601J219N4A Hotshot™ Series Washdown Pump Kit W/Hose, 12V, 6Gpm - P601J-219N-4A - 6-P601J219N4Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetHotShot 3 thru HD5 Include: 2 x 1/2" Straight Hosebarb 2 x 3/4" Straight Hosebarb 1 x 3/4" GHT Adapter HotShot HD6 includes: 2 x 3/4" Straight Hosebarb 1 x 3/4" GHT AdapterHD model feature s heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressuresFull kit version include 25' (7.6m) hose coil
Jabsco P601J219N3A Hotshot™ Series Washdown Pump, 12V, 6Gpm - P601J-219N-3A - 6-P601J219N3Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetIncludes: 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT AdapterHD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures
Jabsco P601J218S3A Par-Max Heavy Duty Water System Pump, 12V, 6Gpm - P601J-218S-3A - 6-P601J218S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco P601J215S3A Par-Max Heavy Duty Water System Pump, 12V, 6Gpm - P601J-215S-3A - 6-P601J215S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco P501J119N4A Hotshot™ Series Washdown Pump Kit W/Hose, 12V, 5Gpm - P501J-119N-4A - 6-P501J119N4Af1
Co-molded diaphragm for long life and durability Efficient and quiet operationSealed pressure switchSelf-primingCan run dry without damageQuick connect portsVibration dampening mountsHotShot 3 thru HD5 Include: 2 x 1/2" Straight Hose barb, 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT Adapter
Jabsco P501J119N3A Hotshot™ Series Washdown Pump, 12V, 5Gpm - P501J-119N-3A - 6-P501J119N3Af1
Co-molded diaphragm technology for long life and durabilityEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityCan run dry without damageQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetIncludes: 2 x 1/2" Straight Hose barb, 2 x 3/4" Straight Hose barb, 1 x 3/4" GHT Adapter HotShotHD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures
Jabsco P501J118S3A Par-Max Heavy Duty Water System Pump, 12V, 5Gpm - P501J-118S-3A - 6-P501J118S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
Jabsco P501J115S3A Par-Max Heavy Duty Water System Pump, 12V, 5Gpm - P501J-115S-3A - 6-P501J115S3Af1
Co-molded diaphragm technology for long life and durability HD model featuring heavy duty, motor and cast aluminum lower housing which allow for long-life, even at high pressuresEfficient and quiet operationIntegrated, sealed pressure switch for on-demand operationSelf-priming allows for installation versatilityRuns Dry Without DamageSelf-PrimingQuick connect ports for ease of installation, servicing, and maintenanceVibration dampening mounting feetEquipped with integrated bypass module to reduce cycling and provide smoother flowQuick Connect Strainer included
