Cook Mfg
Circuit Breaker - 7186 - 119-7186F1
Available for jack plates & tilt trim. Used to eliminate any simple problems that might arise.
Cmc 20122 2° Transom Wedges/Set Back Spacers - 20122 - 119-20122F1
Designed to give extra positive or negative trim. 1/2" x 4" x 11-1/4". Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speedUnique design of the CMC Transom Wedges allows you to also use them as set back spacers, simply stack and invert 2, 4, and 6 setsFit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt patternMade of strong 6061 T6 alloy aluminum (not cast aluminum)
Cmc 52100 Pt-35 12V Tilt N' Trim For 35 Hp & Smaller Motors - 52100 - 119-52100F1
5-1/2" Set Back enhances stability & performance 84° Trim & Tilt1/4" 6061 T6 Extruded aluminum construction w/SS FastenersElectric Hydraulic Actuator rated at 7853 lbs. of thrustAccommodates clamp-on or bolt-on motors - No adapter neededMounting bolts NOT includedOnly 24lbs.
Cmc 65301 Pl65Hs High Speed Hydraulic Power-Lift® Transom Jack W/Gauge - 65301 - 119-65301F1
Will raise V-6 300hp and smaller outboard motors in approximately 8 seconds, twice as fast as the PL-65 model. Ideal for those who want a jack plate for high speed positioning of their outboard motor. Made of 6061 T6 alloy aluminum extrusions and fastened with stainless fasteners. No welds or castings to break. Ideal for fresh or salt water use. Mounting hardware included.
Cmc 65302 Pl65Hs High Speed Hydraulic Power-Lift® Transom Jack W/O Gauge - 65302 - 119-65302F1
Will raise V-6 300hp and smaller outboard motors in approximately 8 seconds, twice as fast as the PL-65 model. Ideal for those who want a jack plate for high speed positioning of their outboard motor. Made of 6061 T6 alloy aluminum extrusions and fastened with stainless fasteners. No welds or castings to break. Ideal for fresh or salt water use. Mounting hardware included.
Cmc 70012 7" Static Jack Plate - 70012 - 119-70012F1
The 7" Static Setback Plate has 1-1/2" of height adjustment at the transom bracket and 1 of height adjustment on the motor bracket. The dimension from the top of the transom to the top of the motor side is 3-1/2". Constructed of extruded 6061-T6 aluminum alloy and stainless steel fasteners.
Cmc Ba-130 Break Away Mount For Outboards Up To Max 130 Hp - 13003 - 119-13003F1
Designed for duck hunters and/or fisherman that use their boat in shallow stumpy areas. It allows small boats and motors to slide over submerged logs or debris at low speeds. Mounted between the boat transom and the outboard motor. It is designed to help minimize damage to the outboard motor and boat transom only when an obstruction is encountered while running at speeds under 5 M.P.H in the forward direction.
Cmc Pt-130 Electric Hydraulic Tilt & Trim - 13002 - 119-13002F1
You get power tilt & trim, better boat handling, more speed, lower fuel consumption and no more back strain. Rated for 130 H.P. and Smaller Motors6" Set Back to Enhance Boat Stability and Performance20° of Trim and a Total of 90° of Tilt and Trim1/2" 6061 T6 Extruded Aluminum Construction with Stainless Steel FastenersElectric Hydraulic Actuator Rated at 7853 lbs. of ThrustStandard B.I.A. (Bolt Hole Pattern)Convenient Adapter Kit Available for Clamp-on MotorsFour Stainless Steel Motor Mounting Bolts Included
Jackplate-Manual 10In - 61012 - 119-61012F1
One Piece Manual Features:^Made of 6061 T6 extruded aluminum alloy^Stainless steel fasteners for maximum strength and durability^Centrally located adjustment screw for positive alignment^5 Vertical adjustment Designed to fit standard B.I.A. bolt patternRated for up to V6 outboards"
Lower Transom Plate - 20032 - 119-20032F1
Made of strong 3/8" 6061 T6 alloy aluminum (not cast aluminum), these transom plates eliminates bolts "biting" into transoms and can more evenly distribute loads on high performance engines.
Manual Power Lift Transom Jack - 65012 - 119-65012F1
One Piece Manual Features:Made of 6061 T6 extruded aluminum alloyStainless steel fasteners for maximum strength and durabilityCentrally located adjustment screw for positive alignment5 Vertical adjustment Designed to fit standard B.I.A. bolt patternRated for up to V6 outboards
Relay - 7122 - 119-7122F1
A completely new wire assembly will work with all of the CMC jack plates and trim & tilts that we have been making since 1990.7122: 12V 40-amp relay has no skirt.
Relay - 7493 - 119-7493F1
A completely new wire assembly will work with all of the CMC jack plates and trim & tilts that we have been making since 1990.7493: 12V 80-amp relay has a skirt, has replaced the 7312 relay and will plug into the same socket. Will not plug into the socket that was designed for the 7122.
Th Marine 7123 Toggle Switch For Cmc Tilt & Trim - 7123 - 119-7123F1
Includes a rubber boot that screws onto the toggle switch to protect from water intrusion.
Upper Transom Plate - 20022 - 119-20022F1
Made of strong 3/8" 6061 T6 alloy aluminum (not cast aluminum), these transom plates eliminates bolts "biting" into transoms and can more evenly distribute loads on high performance engines.
