T-H Marine
T-H Marine Lid & Hatch Support Spring With Molded Nylon Ends 7/16" X 8-1/2" L - Ls-2 - 232-Ls2Dpf1
The stainless steel spring then supports the lid, hatch or cover in the open position. Stainless steel spring with nylon ends for mounting with four countersunk screws (not included).
T-H Marine Louvered Vent Cover 5-5/8" Od, Fits Into 4" Hole - Lv1Dp - 232-Lv1Dpf1
Designed with louvers to eliminate see-thru look and deflect rain. Designed with a flange molded into part so raw edges of cut are hidden and protected.
T-H Marine Louvered Vent Cover 5-5/8" Od, Fits Into 4" Hole - Lv1Fwdp - 232-Lv1Fwdpf1
Designed with louvers to eliminate see-thru look and deflect rain. Designed with a flange molded into part so raw edges of cut are hidden and protected.
T-H Marine Low Profile Bullet Navigation Lights - Led-Lpnav-1-Dp - 232-Ledlpnav1Dpf1
Lowest Footprint of Any Single Color LED Navigation Bow Light 316 Stainless Housing2 Nautical Mile USCG CertificationPort/Starboard Pair
T-H Marine Low Profile Bullet Navigation Lights - Led-Lpnav-2-Dp - 232-Ledlpnav2Dpf1
Lowest Footprint of Any Single Color LED Navigation Bow Light 316 Stainless Housing2 Nautical Mile USCG CertificationPort/Starboard Pair
T-H Marine Low Profile Twist-Out Deck Plate 4" - Dpslp41Dp - 232-Dpslp41Dpf1
Unique and innovative design features a fully overlapping lid and a positive "O" ring seal insuring a watertight fit. Hidden fasteners provide smooth look.
T-H Marine Low Profile Twist-Out Deck Plate 4" - Dpslp42Dp - 232-Dpslp42Dpf1
Unique and innovative design features a fully overlapping lid and a positive "O" ring seal insuring a watertight fit. Hidden fasteners provide smooth look.
T-H Marine Low Profile Twist-Out Deck Plate 6" - Dpslp61Dp - 232-Dpslp61Dpf1
Unique and innovative design features a fully overlapping lid and a positive "O" ring seal insuring a watertight fit. Hidden fasteners provide smooth look.
T-H Marine Low Profile Twist-Out Deck Plate 6" - Dpslp62Dp - 232-Dpslp62Dpf1
Unique and innovative design features a fully overlapping lid and a positive "O" ring seal insuring a watertight fit. Hidden fasteners provide smooth look.
T-H Marine Max-Air Venturi With Face Plate And 6' Tubing - Mav2Ktdp - 232-Mav2Ktdpf1
With face plate and 6' tubingDraws fresh air from outside the livewell and injects tiny air bubbles into the water flowing into the livewell. Aerated water enters the well at a lower level than with traditional spray heads. The reduced restriction of this fitting allows more water to flow from the pump, works well on fresh water intake or recirculation systems. Faceplate can be mounted anywhere above the water line.
T-H Marine Micro Jacker Clamp-On Motor Adapter - Ahjm-Cma-Dp - 232-Ahjmcmaf1
O/B Clamp On Adaptor
T-H Marine Mini Livewell/Courtesy Light Led-Potted, White - Lwlm1Pleddp - 232-Lwlm1Pleddpf1
T-H Marine Mini Livewell/Courtesy Light LED-Potted, White Totally waterproof, can be mounted underwaterNeoprene sealing gasket includedBright 3-element LED bulbFits 5/8" Hole
T-H Marine Mini-Jacker Jack Plate For Outboards Up To 35Hp (Max Wt 150 Lbs.) - Mj1Dp - 232-Mj1Dpf1
Designed for clamp-on mount outboard motors up to 35 hp. Improves performance and handling of smaller or lighter boats. Also allows mounting of long shaft motors to shorter shaft transom boats. Engine mounting surface is 11-1/2" x 10".
T-H Marine Nautical Slam Latch For 2" Hole - Nfsl51Dp - 232-Nfsl51Dpf1
Low profile oval design. UV stable, stainless steel striker plate, fits a 2" hole. Comes with shims/spacers for 1/16" to 7/8" thickness
T-H Marine Nautical Slam Latch For 2" Hole - Nfsl52Dp - 232-Nfsl52Dpf1
Low profile oval design. UV stable, stainless steel striker plate, fits a 2" hole. Comes with shims/spacers for 1/16" to 7/8" thickness
T-H Marine Oetiker Stainless Steel Stepless Ear Clamp Kit With Crimping Tool (Contains 10 Each Of The 15 Most Needed Sizes) - 18500000 - 232-18500000F1
Oetiker one ear hose clamps with mechanical interlock. Specially formed strip edges reduce the risk of damage to the part being clamped. Mechanical interlock allows use of pre-coated materials. Available in key sizes. Uniform compression and increased clamping force. Features: All 304 stainless steel, Narrow band - 7mm, Lightweight designTampering is visibleFull size range for all marine hose Kit Includes:16700001 5.8 - 7.0mm 16700004 7.8 - 9.5mm16700006 8.8 - 10.5mm (3/8) 16700007 9.6 - 11.3mm16700010 10.8 - 13.3mm16700011 11.0 - 13.8mm (1/2)16700012 11.5 - 14.0mm 16700013 12.0 - 14.5mm16700016 13.2 - 15.7mm16700017 14.5 - 17.0mm (5/8)16700020 15.3 - 18.5mm 16700024 17.8 - 21.0mm (3/4)16700031 22.4 - 25.6mm (1)16700037 26.9 - 30.1mm (1-1/8")16700040 28.4 - 31.6mm16705000 34.9 - 38.1mm (1-1/2) 16705989 37.8 - 41.0mm14100396 Standard Jaw Pincers (formerly 14100118)
T-H Marine Pedestal Base Plug Fits 1.77" Bases - Pbp1Dp - 232-Pbp1Dpf1
Seals Pedestal Base When Not in Use Fits All 1.77" BasesSlide Pin for Easy RemovalMolded - Won't Rust or Corrode
T-H Marine Pfac-1 Pontoon Fender Hanger Clips, 1 Pr. - Pfac-1-Dp - 232-Pfac1Dpf1
Easily Snaps onto Pontoon Rails Convenient Way to Attach Docking FendersStylish Gray Composite Material
T-H Marine Pontoon Door Stops With Ribs Fits Up To 1-1/4" Tubing - Ds1Ldp - 232-Ds1Ldpf1
For Pontoon Boats.Injection molded, designed to fit 1-1/4" square tubing. Anti-rattle. Requires no welding. Simple installation with one #10 screw.
T-H Marine Pontoon Door Stops With Ribs Fits Up To 1-1/4" Tubing - Ds1Rdp - 232-Ds1Rdpf1
For Pontoon Boats.Injection molded, designed to fit 1-1/4" square tubing. Anti-rattle. Requires no welding. Simple installation with one #10 screw.
T-H Marine Pontoon Gate Latch Fits 1", 1-1/8" And 1-1/4" Square Tubing - Gl1Dp - 232-Gl1Dpf1
Entire unit installs on gate only Operates on right or left hinged gatesFits 1", 1-1/8" or 1-1/4" square tubePrevents gate from swinging inwardMolded nylon for strengthPrevents rattling
T-H Marine Pontoon Gate Latch Fits 1", 1-1/8" And 1-1/4" Square Tubing - Gl2Dp - 232-Gl2Dpf1
Entire unit installs on gate only Operates on right or left hinged gatesFits 1", 1-1/8" or 1-1/4" square tubePrevents gate from swinging inwardMolded nylon for strengthPrevents rattling
T-H Marine Pro Hi-Jacker Jack Plate With 6" Setback For Outboards Up To 175 Hp - Jp6Pwdp - 232-Jp6Pwdpf1
Constructed of 3/8" high-strength aluminum with a one-piece design with locking bars and a top adjust screw for one wrench adjustment. Maximum 175 hp. 6" setback, 4" vertical adjustment.
T-H Marine Prop Master Propeller Wrench With 9/16" Garboard Drain Socket On Back Fits All 1-1/16" Prop Nuts - Pmw1Dp - 232-Pmw1Dpf1
A 1-1/16" six point socket style wrench made of high tensile strength, indestructible nylon. Resists fuel, sun, salt water, and other chemicals, will not rattle or strip nuts. Will not slip. Reverse side features 9/16" garboard drain plug socket for square heads. Easier to use than channel lock pliers. High visibility color.
T-H Marine Push In Overflow Drain Tube 90 Degree First All T-H 1-1/2" Thru Hulls, 18" L With Screen - Odt290Dp - 232-Odt290Dpf1
These overflow drain tubes feature a tough, flexible vinyl plastic end with a standpipe of white PVC tubing. To use simply insert vinyl end into the opening of thru-hull fitting. To drain livewell or baitwell, simply remove. Can be cut to customer's lengths.
T-H Marine Push In Overflow Drain Tube 90 Degree Fits All 1-1/8" T-H Thru Hulls, 12" L - Odt190Dp - 232-Odt190Dpf1
These overflow drain tubes feature a tough, flexible vinyl plastic end with a standpipe of white PVC tubing. To use simply insert vinyl end into the opening of thru-hull fitting. To drain livewell or baitwell, simply remove. Can be cut to customer's lengths.
T-H Marine Push In Overflow Drain Tube Straight Fits All T-H 1-1/2" Thru Hulls, 18" L With Screen - Odt2Dp - 232-Odt2Dpf1
These overflow drain tubes feature a tough, flexible vinyl plastic end with a standpipe of white PVC tubing. To use simply insert vinyl end into the opening of thru-hull fitting. To drain livewell or baitwell, simply remove. Can be cut to customer's lengths.
T-H Marine Push In Overflow Drain Tube Straight Fits All T-H 1-1/8" Thru Hulls, 12" L - Odt1Dp - 232-Odt1Dpf1
These overflow drain tubes feature a tough, flexible vinyl plastic end with a standpipe of white PVC tubing. To use simply insert vinyl end into the opening of thru-hull fitting. To drain livewell or baitwell, simply remove. Can be cut to customer's lengths.
T-H Marine Push-In Plug For 1-1/2" Thru-Hull Drains - Pp150 - 232-Pp150F1
These push in plugs are used to stop water flow through drains or overflows from baitwell or livewell. Also work well as plugs for sink drains and built in cooler drains. These plugs are injection molded of marine grade PVC for a long lifespan. Plugs feature a pull tab or pull ring for easy removal. They have double seal rings to assure positive sealing.
T-H Marine Quick Release Deck Plate 6" Diameter, Polar White - Dpcam62Dp - 232-Dpcam62Dpf1
Cam hatch holds secure Hidden fasteners in ringEasy to open and closeTextured finish
T-H Marine Quick Release Deck Plate 8" Diameter, Polar White - Dpcam82Dp - 232-Dpcam82Dpf1
Cam hatch holds secure Hidden fasteners in ringEasy to open and closeTextured finish
T-H Marine Replacement Skeg For Bombardier, Evinrude, Johnson, Omc, Yamaha V4 Outboards (40-80 Hp) - Rs3Dp - 232-Rs3Dpf1
Solid cast aluminum. Welds to lower unit. Easily cut to shape.
T-H Marine Replacement Skeg For Bombardier, Evinrude, Johnson, Omc, Yamaha V4 Outboards (85 To 140 Hp) - Rs2Dp - 232-Rs2Dpf1
Solid cast aluminum. Welds to lower unit. Easily cut to shape.
T-H Marine Replacement Skeg For Bombardier, Evinrude, Johnson, Omc, Yamaha V6 Outboards - Rs1Dp - 232-Rs1Dpf1
Solid cast aluminum. Welds to lower unit. Easily cut to shape.
T-H Marine Replacement Skeg For Mercury V6 Outboards And Mercruiser Stern Drives (I/Os) - Rs4Dp - 232-Rs4Dpf1
Solid cast aluminum. Welds to lower unit. Easily cut to shape.
T-H Marine Replacement Spring For All Models Of Hot Foot - Hfs1Dp - 232-Hfs1Dpf1
Replacement spring.
T-H Marine Rfk1Cpdp Chrome Rigging Flange Hose And 4' Of 2" Black Hose - Rfk1Cpdp - 232-Rfk1Cpdpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rfk25Y1Dp Black Rigging Flange Hose And 4' Of 2.5" Black Hose - Rfk25Y1Dp - 232-Rfk25Y1Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rfk25Y2Dp White Rigging Flange Hose And 4' Of 2.5" White Hose - Rfk25Y2Dp - 232-Rfk25Y2Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rfk25Y3Dp Grey Rigging Flange Hose And 4' Of 2.5" Grey Hose - Rfk25Y3Dp - 232-Rfk25Y3Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rfk2Dp White Rigging Flange Hose And 4' Of 2" White Hose - Rfk-2-Dp - 232-Rfk2Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Flange For 2-1/2" Id Hose, Black - Rf-2.5-1-Dp - 232-Rf251Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Flange For 2" Id Hose - Rf1Cpdp - 232-Rf1Cpdpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Flange For 2" Id Hose - Rf1Dp - 232-Rf1Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Flange For 2" Id Hose - Rf2Dp - 232-Rf2Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Flange Hose Union For 2" Hose With 3/4" Fuel Hose Port, Black - Rffhp1Dp - 232-Rffhp1Dpf1
Split design of union allows installation on pre-rigged boats. Fuel hose port fits type A hose. Installs with TH rigging hose.
T-H Marine Rigging Flange Hose Union For 2" Hose, Black - Rfhu1Dp - 232-Rfhu1Dpf1
Split design of union allows installation on pre-rigged boats. Fuel hose port fits type A hose. Installs with TH rigging hose.
T-H Marine Rigging Hose 2" X 50' - Rfh1Dp - 232-Rfh1Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Hose 2" X 50' - Rfh2Dp - 232-Rfh2Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rigging Hose 2" X 50' - Rfh3Dp - 232-Rfh3Dpf1
These components provide an excellent system to protect cables and wiring from dirt, abrasion, sun and water. The rigging flange serves to connect the rigging hose from the engine to the boat. The flange is internally threaded to retain the rigging hose and to make rigging adjustments easy. The back side of the flange is textured to allow inverted mounting. The rigging hose is durable, flexible, and kink resistant and is commonly found on many new boats.
T-H Marine Rmc102Mgdp Troll-Tamer Trolling Motor Stabilizer Lock For Motorguide Tour Series - Rmc-102Mg-Dp - 232-Rmc102Mgdpf1
Machined from 300 series stainless steel, the Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, it has been designed and tested in the nastiest conditions by top touring pros. Prevents Damage to Trolling MotorsLocks Motor to Deck SecurelyLocking Pin with Quick Release Toe Kick BaseAll Stainless Steel © No Rust or Corrosion
T-H Marine Rod Tamer Rod Straps - Rt14Dp - 232-Rt14Dpf1
Deck MountMolded of black polyurethane material that will retain its stretch and remain unaffected by sunlight and most chemicals. Will not get hung up on fish hooks, lose their hold when wet, or fade. The strap stretches over rods and hooks into a loop mounted on the deck. (Mounts with one countersunk screw).
T-H Marine Rod Tamer Rod Straps - Rt18Dp - 232-Rt18Dpf1
Deck MountMolded of black polyurethane material that will retain its stretch and remain unaffected by sunlight and most chemicals. Will not get hung up on fish hooks, lose their hold when wet, or fade. The strap stretches over rods and hooks into a loop mounted on the deck. (Mounts with one countersunk screw).
T-H Marine Rod Tamer Rod Straps, 12" Gunwale Mount, Holds Up To 3 Rods - Rhd1Dp - 232-Rhd1Dpf1
Strap is molded of black poly material that mounts on the gunnel and stretches to hook to a loop mounted on the deck. Installs very easily in a 3/4" diameter hole with the black stainless steel screws that are included. Strap retracts into the gunnel when not in use.
T-H Marine Saf-T-Stop™ Ignition Kill Switch For Single Outboard - Ks1Dp - 232-Ks1Dpf1
Meets all requirements for emergency stop switches Strong coiled lanyardIsolated circuits on dual units to prevent feedbackMounts anywhere - requires 1-1/2" hole
T-H Marine Screw Down Deck Plate 10" Od, Fish White - Sdp3Fwdp - 232-Sdp3Fwdpf1
Screw down deck plates are an inexpensive alternative to screw-out deck plates. They have a matte finish and are made from strong, super tough poly material.
T-H Marine Screw Down Deck Plate 5-5/8" Od, Black - Sdp1Dp - 232-Sdp1Dpf1
Screw down deck plates are an inexpensive alternative to screw-out deck plates. They have a matte finish and are made from strong, super tough poly material.
T-H Marine Screw Down Deck Plate 8" Od, Black - Sdp2Dp - 232-Sdp2Dpf1
Screw down deck plates are an inexpensive alternative to screw-out deck plates. They have a matte finish and are made from strong, super tough poly material.
T-H Marine Screw In Overflow Drain Tube Fits 1-1/8" Threaded Drain With Top Screen Glued, 12" L - Odt112Gstw - 232-Odt112Gstwf1
Includes top screen Threaded sealUnscrew half way to expose drain holes
T-H Marine Shark Eye Nav Lights 1Nm (Pair) - Sel1Dp - 232-Sel1Dpf1
T-H Marine Shark Eye Nav Lights 1NM (Pair) Meets ABYC A-16 & USGC 1 NMNMMA type acceptedStainless steel baseTin wirePair: (1) Red, (1) Green
T-H Marine Ss3Dp Steer-Stop™ Outboard Hydraulic Steering Lock - Ss-3-Dp - 232-Ss3Dpf1
Locks hydraulic steering when traileringFits most steering cylinder rods on outboard enginesSnaps over outboards hydraulic steering cylinder rodsHelps keep engine centered during transportProtects steering system, outboard, and motor supportsIncludes cord to connect units for storage and to aid in removalGrip makes it even simpler and easier to put on and take off
T-H Marine Stainless Steel Cup Holder - Lch1Ssdp - 232-Lch1Ssdpf1
Top quality stainless steel. Fits most existing cup holes. Drain fits 3/8" hose.
T-H Marine Stainless Steel Wire Mesh Strainer Fits Aerator Pump Intake - As1Dp - 232-As1Dpf1
Protects pumps from debris or bait fish. Formed wire mesh - molded PVC threaded base.
T-H Marine Stainless Steel Wire Mesh Strainer Fits Th1, 1Xl, 90, 92 Thru-Hulls - As2Dp - 232-As2Dpf1
Protects pumps from debris or bait fish. Formed wire mesh - molded PVC threaded base.
T-H Marine Straight Extra Long Thru-Hull Fitting For Hose, White - Th1202Xldp - 232-Th1202Xldpf1
High Quality UV and Chemical Resistant Virgin PolyproSized to Fit All Marine Hose
T-H Marine Straight Extra Long Thru-Hull Fitting For Hose, White - Th752Xldp - 232-Th752Xldpf1
High Quality UV and Chemical Resistant Virgin PolyproSized to Fit All Marine Hose
T-H Marine Straight Thru-Hull Fitting For Hose, White - Th1202Dp - 232-Th1202Dpf1
High Quality UV and Chemical Resistant Virgin PolyproSized to Fit All Marine Hose
T-H Marine Straight Thru-Hull Fitting For Hose, White - Th1502Dp - 232-Th1502Dpf1
High Quality UV and Chemical Resistant Virgin PolyproSized to Fit All Marine Hose
T-H Marine Sure-Seal Deck Plate 6", Sand Shell - Dps63Dp - 232-Dps63Dpf1
Screw-Out StyleFeatures a fully overlapping lid and a positive 'O' ring seal insuring a watertight fit. No visible mounting fasteners. Total UV & chemical stability. No tools required for opening.
T-H Marine Sure-Seal Deck Plate 8" - Dps81Dp - 232-Dps81Dpf1
Screw-Out StyleFeatures a fully overlapping lid and a positive 'O' ring seal insuring a watertight fit. No visible mounting fasteners. Total UV & chemical stability. No tools required for opening.
T-H Marine Sure-Seal Deck Plate 8" - Dps82Dp - 232-Dps82Dpf1
Screw-Out StyleFeatures a fully overlapping lid and a positive 'O' ring seal insuring a watertight fit. No visible mounting fasteners. Total UV & chemical stability. No tools required for opening.
T-H Marine Torque Tab - Tab1Dp - 232-Tab1Dpf1
Eliminates or reduces right hand steering torque caused by jacked-up transom heights and high pitched propellers. Inexpensive, simple to install and does not reduce speed. Cast aluminum construction complete with installation hardware and instructions.
T-H Marine Transom Support Plate, Lower Bolt Holes - Standard - Tsp2Dp - 232-Tsp2Dpf1
Distributes the stress of the motor mounting boltsHigh quality cast aluminum 3/8" thickness
T-H Marine Transom Support Plate, Top Bolt Holes-Standard - Tsp1Dp - 232-Tsp1Dpf1
Distributes the stress of the motor mounting boltsHigh quality cast aluminum 3/8" thickness
T-H Marine Trim Handle - Ejt1Dp - 232-Ejt1Dpf1
Mounted directly to the throttle and shift lever for maximum safety and ease of operation. The switches are push button, weather proof and rated above what is required to operate a trim unit. Pre 1979 OMC.
T-H Marine Troll-Tamer Trolling Motor Stabilizer Lock - Rmc105Fmkdp - 232-Rmc105Fmkdpf1
Machined from 300 series stainless steel, the Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, it has been designed and tested in the nastiest conditions by top touring pros. Prevents Damage to Trolling MotorsLocks Motor to Deck SecurelyLocking Pin with Quick Release Toe Kick BaseAll Stainless Steel © No Rust or Corrosion
T-H Marine Ttc1Dp Transom Trim Control - Ttc1Dp - 232-Ttc1Dpf1
Put a trim switch or hydraulic jack plate anywhere you want with this versatile switch. The Transom Trim Control Switch provides a weatherproof tilt control system at the stern area of the boat to facilitate placing motor support in position with one person. Switch can also be used for remote adjustment of hydraulic jack plates. The switch housing is molded black plastic with raised white letters and may be mounted on any flat surface, comes with 18" pigtail wire and installation instructions. Trim switch for outboards or stern drivesHydraulic jack plate switchWaterproof push button switchesPuts tilt & trim control anywhere you want itUV stable molded housing
T-H Marine Utility/Rod Grommets (Pair), Black - Ug1Dp - 232-Ug1Dpf1
Molded of tough, flexible, vinyl. It is designed for multiple uses in boats, such as cable pass thru, landing net holder, fishing rod support or protector, stern light holder or any number of other uses. For bulk head pass-thru, simply mount and run cables, wires, etc. through to prevent chafing. For land nets, fishing rods, stern light or other items, simply mount and insert items to be protected or held in place. To remove items from utility grommet, simply pull. This utility grommet can be used either horizontal or vertical. Install with four (4) pan head screws (not furnished).
T-H Marine Utility/Rod Grommets (Pair), Black - Ug2Dp - 232-Ug2Dpf1
Molded of tough, flexible, vinyl. It is designed for multiple uses in boats, such as cable pass thru, landing net holder, fishing rod support or protector, stern light holder or any number of other uses. For bulk head pass-thru, simply mount and run cables, wires, etc. through to prevent chafing. For land nets, fishing rods, stern light or other items, simply mount and insert items to be protected or held in place. To remove items from utility grommet, simply pull. This utility grommet can be used either horizontal or vertical. Install with four (4) pan head screws (not furnished).
T-H Marine Waterproof Blue Led Lighted Rim Drink Holder - Led-Lch-Bu-Dp - 232-Ledlchbudpf1
Illuminated Cup Holder Provides Soft LED Lighting 15 Super Bright LEDsRobust UV Stable Molded HousingMounts in Standard 3-5/8" HoleCorrosion Resistant 316 Stainless Steel Rim for a Sleek, Finished LookLED Light System is WaterproofIncludes Drain Hole and Nipple for Routing DrainageWired for 12V
T-H Marine Waterproof Extreme Led Underwater Light - Led-Sm171Cob-W-Dp - 232-Ledsm171Cobwdpf1
Extreme Output LED Underwater Light - Surface Mount 20% Brighter than Our Standard LED Underwater Light3.5"x1.5"High Impact Polymer ConstructionCompletely Waterproof - For Use Underwater or Above WaterPolarity and Thermal Protection
T-H Marine Waterproof Extreme Led Underwater Light - Led-Sm172Cob-B-Dp - 232-Ledsm172Cobbdpf1
Extreme Output LED Underwater Light - Surface Mount 20% Brighter than Our Standard LED Underwater Light3.5"x1.5"High Impact Polymer ConstructionCompletely Waterproof - For Use Underwater or Above WaterPolarity and Thermal Protection
T-H Marine Waterproof Extreme Led Underwater Light - Led-Sm173Cob-G-Dp - 232-Ledsm173Cobgdpf1
Extreme Output LED Underwater Light - Surface Mount 20% Brighter than Our Standard LED Underwater Light3.5"x1.5"High Impact Polymer ConstructionCompletely Waterproof - For Use Underwater or Above WaterPolarity and Thermal Protection
T-H Marine Waterproof Stainless Steel Led Underwater Light - Led-Sm7815-B-Dp - 232-Ledsm7815Bf1
This surface mount, stainless steel underwater light is highly attractive, with superior brightness and durable construction. Completely waterproof, this 316 stainless steel bezel light will last for many years in the toughest marine environments. 5.7"x1.7" . Overheat ProtectionResistant to Corrosion, UV and ChemicalsFully Sealed and Waterproof Light - IP68 RatedVery Easy to Install with Two (2) Screws and Small Wiring HoleSix (6) Super Bright LED Diodes
T-H Marine Waterproof White Led Lighted Rim Drink Holder - Led-Lch-W-Dp - 232-Ledlchwdpf1
Illuminated Cup Holder Provides Soft LED Lighting 15 Super Bright LEDsRobust UV Stable Molded HousingMounts in Standard 3-5/8" HoleCorrosion Resistant 316 Stainless Steel Rim for a Sleek, Finished LookLED Light System is WaterproofIncludes Drain Hole and Nipple for Routing DrainageWired for 12V
T-H Marine Z-Lock Manual Jack Plate For All V6 Outboards Up To 300Hp - Jpz6Dp - 232-Jpz6Dpf1
Built with full 1/2" aluminum with an exclusive Z-Lock design for the ultimate in strength and virtually no side slippage or movement, this jack plate handles all V6 outboards up to 300hp. Easily adjustable with a single center bolt adjustment point.
T-H Marine Zl-15 Z-Launch™ Launch Cord, 15' - Zl-15-Dp - 232-Zl15Dpf1
For solo watercraft launching. The no-hassle launch cord, made of premium elastics, uses automatically adjusting tension when you back your boat, jet ski, or tow tube into the water, so it won't jerk your watercraft around when you pull the trailer forward. Fasten a hook to your trailer, connect a steel ring to the winch, and lock the winch. You're ready for the smoothest watercraft launching on the water. No-hassle designAttaches easilyStay safe and dry launching your boat aloneGreat for ramps with "no power" lawsBoats 23' to 35' use 20' cordBoats 17' to 22' use 15' cordBoats to 16' use 10' cord
T-H Premium Underwater Light - Led-39060-Dp - 232-Led39060Dpf1
Six (6) High Intensity Super Bright LEDs Newest Generation in LED TechnologyStainless Steel Bezel for Beauty and DurabilitySurface Mount Installation - No Large HolesResists Rust and Corrosion3/8" Hole for Wire
T-H Premium Underwater Light - Led-39061-Dp - 232-Led39061Dpf1
Six (6) High Intensity Super Bright LEDs Newest Generation in LED TechnologyStainless Steel Bezel for Beauty and DurabilitySurface Mount Installation - No Large HolesResists Rust and Corrosion3/8" Hole for Wire
T-H Premium Underwater Light - Led-39062-Dp - 232-Led39062Dpf1
Six (6) High Intensity Super Bright LEDs Newest Generation in LED TechnologyStainless Steel Bezel for Beauty and DurabilitySurface Mount Installation - No Large HolesResists Rust and Corrosion3/8" Hole for Wire
T-H Underwater Light With Stainless Steel Bezel - Led-51900-Dp - 232-Led51900Dpf1
316 Stainless Steel Bezel Six Bright LEDs - Lights Up TransomsNo High Heat - Can Be Used Above Water
T-H Underwater Light With Stainless Steel Bezel - Led-51901-Dp - 232-Led51901Dpf1
316 Stainless Steel Bezel Six Bright LEDs - Lights Up TransomsNo High Heat - Can Be Used Above Water
Th Marine Bwk2Dp Baitwell Aeration & Pumping Kit - Bwk2Dp - 232-Bwk2Dpf1
Kit contains:ODT-190: 90° overflow drain tubeTH-1202: 5/8"-1-1/4" thru-hullAHV-2: valved aeration head w/shutoffDAH-90: directional aerator headTEE 3/4"
Th Marine Elct0078 Standard Actuator - Elct0078 - 232-Elct0078 Superseded By: 232-7050F1
Hydraulic Actuators are completely self contained with their own fluid reservoir. They incorporate the pump, motor, reservoir and cylinder all in the same body. This eliminates the need for multiple hydraulic components such as hoses, pumps and cylinders. Actuator can be utilized in almost any type of environment. Made of 100% non-ferrous materials, they are totally submersible. They contain a no-leak seal and wiper that keeps dirt and water out of the working parts.Fits: CMC Power-Lift hyd. jack plates (models: 61001, 61002, 65001, 65002, 65201)CMC Power Tilt & Trim Units (PT-35 & PT-130 models: 13001, 13002, 52100)ATLAS Tilt & Trim Units (models: THT-35C-DP, THT-130C-DP, THT-130CGK-DP)
Th Marine Flx125Dp 1-1/4 X 50' Th Flex™ Sleeving, Black - Flx125Dp - 232-Flx125Dpf1
A lightweight jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H Flex™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H Flex™ easy to slip on. Lightweight Protective SleevingProtects Wire, Cables and HosesBraided from High Temperature YarnsChemical ResistantSimplifies and beautifies any rigging application
Th Marine Flx150Dp 1-1/2 X 50' Th Flex™ Sleeving, Black - Flx150Dp - 232-Flx150Dpf1
A lightweight jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H Flex™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H Flex™ easy to slip on. Lightweight Protective SleevingProtects Wire, Cables and HosesBraided from High Temperature YarnsChemical ResistantSimplifies and beautifies any rigging application
Th Marine Flx50Dp 1/2 X 100' Th Flex™ Sleeving, Black - Flx50Dp - 232-Flx50Dpf1
A lightweight jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H Flex™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H Flex™ easy to slip on. Lightweight Protective SleevingProtects Wire, Cables and HosesBraided from High Temperature YarnsChemical ResistantSimplifies and beautifies any rigging application
