Hubbell
Toggle Swch On/Off Double Pole - M21Sp - 36-M21Spf1
On in parenthesis (On) indicates a momentary position.
Toggle On/Off/On Dbl.Pole - M223Sp - 36-M223Spf1
On in parenthesis (On) indicates a momentary position.
Toggle Momentary On/Off/On - M123Msp - 36-M123Mspf1
On in parenthesis (On) indicates a momentary position.
Thermoplastic Fd Box, Yellow - Hbl60Cm83A - 36-Hbl60Cm83Af1
Type FD (deep). Molded ridge around face further prevents water from getting between box and cover plate. 4-9/16" high x 2-15/16" wide x 3-1/4" deep. Has a 22 cubic inch capacity.
Shore Power Inlet - M4100B12R - 36-M4100B12Rf1
Yellow Supertough® nylon. Shore power inlet has gasketed, spring loaded cover which closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4-7/8" on centers and rear portions is 3-15/16" dia. Mounting screws and gasket included.
Rubber Boot - Msb1 - 36-Msb1F1
Black silicone rubber bonded to brass nut. Provides positive seal against moisture, oil, etc. Fits any non-lighted toggle switch.
Replacement Plug - M5100P9 - 36-M5100P9F1
Yellow Zytel® super tough nylon watertight plug has gasketed locking ring to make plug/receptacle interface watertight. Cord grip range is 1.00-1.94 in. (25.4-49.3).
Replacement Plug - M4100P12 - 36-M4100P12F1
Yellow Zytel® super tough nylon watertight plug has gasketed locking ring to make plug/receptacle interface watertight. Cord grip range is 1.00-1.94 in. (25.4-49.3).
Replacement Interior F/60Cm61 - Hbl303Int - 36-Hbl303Intf1
Stainless steel power outlet has gasketed, self-closing cover, watertight when cover is screwed in place. Mounting holes are 2-3/8" (60.3) on centers. Mounting screws and gasket included.
Replacement Connector Body - M5100C9R - 36-M5100C9Rf1
Yellow Supertough® nylon watertight connector body has gasketed locking ring to make inlet/connector interface watertight. Cord grip range is 1.000-1.940" (25.4-49.3).This device mates with shore power inlet only.
Replacement Connector Body - M4100C12R - 36-M4100C12Rf1
Yellow Supertough® nylon watertight connector body has gasketed locking ring to make inlet/connector interface watertight. Cord grip range is 1.000-1.940" (25.4-49.3).This device mates with shore power inlet only.
Receptacle - M5100R9 - 36-M5100R9F1
Gray Supertough® nylon dockside receptacle has gasketed, spring-loaded cover. Closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4-7/8" (123.8) on centers. Mounting screws and gasket included.
Receptacle - M4100R12 - 36-M4100R12F1
Gray Supertough® nylon dockside receptacle has gasketed, spring-loaded cover. Closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4-7/8" (123.8) on centers. Mounting screws and gasket included.
Plastic Switch/Outlet Box - Hbl6079 - 36-Hbl6079F1
Provides secure mounting means. Ears at top and bottom pull box tightly against wall. Support strap is provided which pulls box to backside of wall.
Non-Metallic 30A 125V Shore - Hbl303Nmbl - 36-Hbl303Nmblf1
Interior has easy-to-wire terminations and is transparent for quick and easy visual inspection. Mounting holes are 2-3/8" on centers. Mounting screws, gasket and protective rear enclosure is included.
Hubbell Yq230 Yellow Intelligent "Y" (1) 50A 125V/250V Female To (2) 30A 125V Male Adapters - Yq230 - 36-Yq230F1
Safely powers 50 amp 125/250 volt boat from (2) 30 amp 125 volt receptacles at dockside. 4-pole contactor breaks both hots and both neutrals to prevent possible "live" plug when not engaged. UV resistant housing, 30 amp plug that connects to 30 amp shore power, safety indicator light, internal cord clamps, sealing grommets, anti-fog-rain-humidity environmental seal, 50 amp connector body that mates with boat cord set and Hubbell connector and plugs. Shuts off power if improper wiring condition exists on power center or if 1 plug is not fully engaged. Senses polarity of 30 amp receptacle on dock and (2) 30 amp receptacles from opposite phases.Note: The YQ230 Adapter will only work with two 30A receptacles that are on different phases. Not CSA Approved.
Hubbell Yellow "Y" Female To Male Adapter - Hbl64Cm57 - 36-Hbl64Cm57F1
Fully molded water tight design.
Hubbell Yellow "Y" Female To Male Adapter - Hbl64Cm56 - 36-Hbl64Cm56F1
Fully molded water tight design.
Hubbell Yellow "Y" Female To Male Adapter - Hbl64Cm54 - 36-Hbl64Cm54F1
Fully molded water tight design.
Hubbell Weatherproof 50A 125 Volt Shore Power Inlet - Hardware Included - Hbl503Ss - 36-Hbl503Ssf1
Mounting holes are 2-3/8" on centers and match existing mounting patterns. Mounting screws and gasket included.SS models have a gasketed, self-closing cover, making it watertight when fastened.
Hubbell Nickel Plated Brass Heat Resistant 50A Plug - Hbl63Cm65 - 36-Hbl63Cm65F1
50 Amp, 125/250 Volt. Nickel plated brass. Heat resistant thermoset interior and combination metal and rubber cord grip, which provides superior strain relief capability. Cord grip range is .44-1.140".
Hubbell Nickel Plated Brass Heat Resistant 50A Plug - Hbl63Cm61 - 36-Hbl63Cm61F1
50 Amp, 125/250 Volt. Nickel plated brass. Heat resistant thermoset interior and combination metal and rubber cord grip, which provides superior strain relief capability. Cord grip range is .44-1.140".
Hubbell Nickel Plated Brass Heat Resistant 50A Connector Body - Hbl63Cm64 - 36-Hbl63Cm64F1
50 Amp, 125/250 Volt. Nickel plated brass. Heat resistant thermoset interior and combination metal and rubber cord grip, which provides superior strain relief capability. Cord grip range is .44-1.140".
Hubbell Nickel Plated Brass Heat Resistant 50A Connector Body - Hbl63Cm60 - 36-Hbl63Cm60F1
50 Amp, 125/250 Volt. Nickel plated brass. Heat resistant thermoset interior and combination metal and rubber cord grip, which provides superior strain relief capability. Cord grip range is .44-1.140".
Hubbell Marine Isolation Transformer, White Powder Coat, 15 Kva, 60 Hz - Hbl50Aitw - 36-Hbl50Aitwf1
Isolation Transformers for the Marine industry. Suitable for 100 Amp shore power systems, UL Listed isolation transformers assure proper wiring conditions on your boat, and greatly minimizes the possibility of stray current from entering the water. Electrical grade silica and resin compounds completely enclose the core and coil to seal out all moisture and air. UL Type 3R enclosure for indoor or outdoor service. Encapsulation eliminates corrosion and insulation deterioration. UL listed, CSA certified and UL-3R enclosures meets or exceeds all listing criteria including NEMA, ANSI and OSHA standardsShielded for cleaner powerEncapsulated and completely enclosed designQuiet operation with sound levels well below NEMA standardsLong life UL class 155°C insulation system
Hubbell Heat Resistant Thermoset Base Single 50A Receptacle - Hbl63Cm70 - 36-Hbl63Cm70F1
Features heat resistant thermoset base.
Hubbell Heat Resistant Thermoset Base Single 50A Receptacle - Hbl63Cm69 - 36-Hbl63Cm69F1
Features heat resistant thermoset base.
Hubbell Hblt26Cm11 30A Twist-Lock® Circuit Tester - Hblt26Cm11 - 36-Hblt26Cm11F1
Styled and sized like a standard Hubbell Twist-Lock® Plug. Simply plug it in and the LED back panel immediately identifies if the connections are made correctly and are in the correct position, ensuring the device is wired properly. An easy to read card is provided with the tester, to help determine if the connections are correct. This tester is compact and can easily clip onto your tool belt. The Hubbell Circuit Tester is UL and C-UL Listed.
Hubbell Hbl77Cm74Wo Yellow Valox® Carbonate Lift Cover Plate For Weatherproofing 50A Receptacles - Hbl77Cm74Wo - 36-Hbl77Cm74Wof1
Valox® carbonate. For weatherproofing 50 amp receptacles. Meets the requirements of the most stringent of UL's three listing categories for weatherproof plates. Stainless steel screws and a neoprene gasket are included for mounting. Made for mounting to FS/FD type weatherproof boxes.
Hubbell Hbl77Cm17 Yellow Seal-Tite Cover For Weatherproofing Connector Bodies - Hbl77Cm17 - 36-Hbl77Cm17F1
For weatherproofing connector bodies when used on extension cords or adapters.
Hubbell Hbl77Cm16 Yellow Seal-Tite Cover For Weatherproofing 50A Plugs - Hbl77Cm16 - 36-Hbl77Cm16F1
For weatherproofing 50 amp plugs
Hubbell Hbl77Cm15 Yellow Seal-Tite Cover & Stainless Steel Sealing Ring For Connector Body - Hbl77Cm15 - 36-Hbl77Cm15F1
For connector bodies when used with shore power inlets. Stainless steel threaded sealing ring makes connection watertight.
Hubbell Hbl74Cm25Woaw White Polycarbonate Spring Loaded Weatherproof Cover, White - Hbl74Cm25Woaw - 36-Hbl74Cm25Woawf1
White polycarbonate. Spring loaded. For weatherproofing 26CM10 receptacle. Meets the most stringent requirements of UL's three listing categories for weatherproof plates. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes.
Hubbell Hbl74Cm25Woa Polycarbonate Spring Loaded Weatherproof Cover, Yellow - Hbl74Cm25Woa - 36-Hbl74Cm25Woaf1
Yellow polycarbonate. Spring loaded. For weatherproofing 26CM10 receptacle. Meets the most stringent requirements of UL's three listing categories for weatherproof plates. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes.
Hubbell Hbl74Cm24Wo Polycarbonate Spring Loaded Weatherproof Cover, Yellow - Hbl74Cm24Wo - 36-Hbl74Cm24Wof1
Yellow polycarbonate. Spring loaded. For weatherproofing old style 26CM10 receptacle. Meets the most stringent requirements of UL's three listing categories for weatherproof plates. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes.
Hubbell Hbl61Cm72 Yellow Twist Lock Female To Twist Lock Male Adapter - Hbl61Cm72 - 36-Hbl61Cm72F1
Fully molded, watertight design.
Hubbell Hbl61Cm71 Yellow Twist Lock Female To Twist Lock Male Adapter - Hbl61Cm71 - 36-Hbl61Cm71F1
Fully molded, watertight design.
Hubbell Hbl61Cm64 Compact Gray Nylon Weatherproof Panel Mount Inlet - Hbl61Cm64 - 36-Hbl61Cm64F1
Compact Grey nylon panel mount inlet ideal for bass boat battery charging connection. Has gasketed spring-loaded lift cover for weatherproofing front and neoprene boot for weatherproofing rear. Will accept both 15A 125V and 20A 125V 2 pole, 3 wire straight blade connector bodies. 15 Amp 125 Volt.
Hubbell Hbl61Cm56 Yellow Twist Lock Female To Twist Lock Male Adapter - Hbl61Cm56 - 36-Hbl61Cm56F1
Fully molded, watertight design.
Hubbell Hbl61Cm55 Yellow Twist Lock Female To Twist Lock Male Adapter - Hbl61Cm55 - 36-Hbl61Cm55F1
Fully molded, watertight design.
Hubbell Hbl61Cm42 Yellow 50A 125/250V Vinyl Jacketed Pre Wired 25' Shore Power Cable Set - Hbl61Cm42 - 36-Hbl61Cm42F1
Vinyl jacketed. Completely factory pre-wired with molded-on devices. Connector end has a threaded sealing ring for making the inlet/connector interface watertight.LED models have two high density LED indicator lights. Bright green indicates "power on".
Hubbell Hbl60Cm33 Yellow Seal-Tite Cover For 26Cm13 Connector Body - Hbl60Cm33 - 36-Hbl60Cm33F1
For 26CM13 connector body when used with shore power inlets. Yellow. Threaded sealing ring makes connection watertight. Also for weatherproofing 26CM11 plug when used with 60CM63 power outlet. Fits Insulgrip devices only.
Hubbell Hbl60Cm31 Yellow Seal-Tite Cover For Weatherproofing Hbl26Cm11 Plug - Hbl60Cm31 - 36-Hbl60Cm31F1
For weatherproofing 26CM11 plugFits Insulgrip® devices onlyYellow
Hubbell Hbl52Cm69Cyellow 15A 125V Connector Body - Hbl52Cm69C - 36-Hbl52Cm69Cf1
Rugged nylon housing and detachable cord grip (range .230-.720") that utilizes unique offset jaws arrangement to provide secure strain relief. Yellow15 Amp 125 Volt
Hubbell Hbl52Cm66C Yellow 15A 125V Insulgrip Plug - Hbl52Cm66C - 36-Hbl52Cm66Cf1
Rugged nylon housing and detachable cord grip (range .230-.720") that utilizes unique offset jaws arrangement to provide secure strain relief. Yellow15 Amp 125 Volt
Hubbell Hbl52Cm62 Yellow 15A 125V Heat & Corrosion Resistant Duplex Receptacle - Hbl52Cm62 - 36-Hbl52Cm62F1
Features heat resistant melamine body and abuse resistant nylon face. Use where salt or other corrosive elements are a problemYellow corrosion resistant duplex receptacle15 Amp 125 Volt
Hubbell Hbl52Cm21 Yellow Spring Loaded Polycarbonate Lift Cover Plate For Weatherproofing Duplex Receptacles - Hbl52Cm21 - 36-Hbl52Cm21F1
Spring-loaded polycarbonate. For weatherproofing duplex receptacles. Stainless steel screws. Neoprene gasket. For FS/FD type weatherproof boxes.
Hubbell Hbl5200 Black 125V Outlet Circuit Tester - Hbl5200 - 36-Hbl5200F1
A simple arrangement of neon lights which visually indicates correct wiring, reverse polarity, open ground, neutral or hot wire, hot and ground reversed, hot wire on neutral terminal and hot terminal unwired. Simply plug into a single phase 125 volt, 2 pole, 3 wire outlet and combination of lit/unlit lamps will immediately indicate condition of circuit. Instructions and symbol identification are printed on durable polyester labels permanently attached to tester. Can test other 2 pole, 3 wire phase 125 volt outlets with proper use of correct adapter.
Hubbell Hbl328Dcr Yellow Electric Fishing Reel 30A 28Vdc Receptacle - Hbl328Dcr - 36-Hbl328Dcrf1
Until now, larger electric fishing reel systems typically utilized AC rated corrosion resistant connectors since there were no DC rated devices. Hubbell's DC rated locking electric fishing reel system features a corrosion resistant connectors which can be used along with a Hubbell outlet box and weatherproof cover plate to complete the installation. These devices are all rated at 28 VDC and are applicable for all 12, 24 and 32 volt DC fishing reel systems. Made of high-visibility yellow nylon that is impact resistant and UV stabilized for longer life. Nickel plated contacts for corrosion resistance. UL listed and CSA certified.
Hubbell Hbl328Dcp Yellow Electric Fishing Reel 30A 28Vdc Male Plug - Hbl328Dcp - 36-Hbl328Dcpf1
Until now, larger electric fishing reel systems typically utilized AC rated corrosion resistant connectors since there were no DC rated devices. Hubbell's DC rated locking electric fishing reel system features a corrosion resistant connectors which can be used along with a Hubbell outlet box and weatherproof cover plate to complete the installation. These devices are all rated at 28 VDC and are applicable for all 12, 24 and 32 volt DC fishing reel systems. Made of high-visibility yellow nylon that is impact resistant and UV stabilized for longer life. Nickel plated contacts for corrosion resistance. UL listed and CSA certified.
Hubbell Hbl328Dcc Yellow Electric Fishing Reel 30A 28Vdc Female Connector - Hbl328Dcc - 36-Hbl328Dccf1
Until now, larger electric fishing reel systems typically utilized AC rated corrosion resistant connectors since there were no DC rated devices. Hubbell's DC rated locking electric fishing reel system features a corrosion resistant connectors which can be used along with a Hubbell outlet box and weatherproof cover plate to complete the installation. These devices are all rated at 28 VDC and are applicable for all 12, 24 and 32 volt DC fishing reel systems. Made of high-visibility yellow nylon that is impact resistant and UV stabilized for longer life. Nickel plated contacts for corrosion resistance. UL listed and CSA certified.
Hubbell Hbl31Cm29 White 15A/20A 125V Straight Blade Female To 30A 125V Twist Lock Male Adapter - Hbl31Cm29 - 36-Hbl31Cm29F1
Permits use of 15 amp or 20 amp 125 volt straight blade plug with 30 amp 125 volt twist-lock locking type receptacle. Not recommended for use in wet locations.
Hubbell Hbl31Cm28 White 30A 125V Twist Lock Female To 15A 125V Straight Blade Male Adapter - Hbl31Cm28 - 36-Hbl31Cm28F1
Permits use of 30 amp 125 volt twist-lock locking type plug with 15 amp 125 volt straight blade receptacle. Not UL listed. Not recommended for use in wet locations.
Hubbell Hbl305Crr Yellow 30A 125V Locking Receptacle - Hbl305Crr - 36-Hbl305Crrf1
Yellow melamine with all nickel plated components, back wired.
Hubbell Hbl305Crp Yellow 30A 125V Locking Plug - Hbl305Crp - 36-Hbl305Crpf1
Yellow nylon body, nickel plated contacts, triple grip nylon cord clamp, individual wire pockets for easy wire terminations.
Hubbell Hbl305Crc Yellow 30A 125V Connector Body - Hbl305Crc - 36-Hbl305Crcf1
Yellow nylon body, nickel plated contacts, triple grip nylon cord clamp, individual wire pockets for easy wire terminations.
Hubbell Hbl303Sso Watertight Stainless Steel 30A 125V Shore Power Outlet - Hardware Included - Hbl303Sso - 36-Hbl303Ssof1
Stainless steel power outlet has gasketed, self-closing cover, watertight when cover is screwed in place. Mounting holes are 2-3/8" (60.3) on centers. Mounting screws and gasket included.
Hubbell Hbl303Ss Stainless Steel 30A 125V Shore Power Inlet - Hardware Included - Hbl303Ss - 36-Hbl303Ssf1
Interior has easy-to-wire terminations and is transparent for quick and easy visual inspection. Mounting holes are 2-3/8" on centers. Mounting screws, gasket and protective rear enclosure is included.
Hubbell Hbl26Cm13 Yellow 30A 125V Twist Lock Connector Body - Hbl26Cm13 - 36-Hbl26Cm13F1
Rugged nylon housing and cord grip (range .385-.780") that utilizes unique offset jaws arrangement to provide secure strain relief.Yellow30 Amp 125 Volt Twist-Lock®
Hubbell Hbl26Cm11 Yellow 30A 125V Twist Lock Insulgrip Plug - Hbl26Cm11 - 36-Hbl26Cm11F1
Rugged nylon housing and cord grip (range .385-.780") that utilizes unique offset jaws arrangement to provide secure strain relief.Yellow30 Amp 125 Volt Twist-Lock®
Hubbell Hbl26Cm10 Yellow 30A 125V Twist Lock Heat Resistant Rynite Body Single Receptacle - Hbl26Cm10 - 36-Hbl26Cm10F1
Single receptacle has heat resistant Rynite° body and abuse resistant nylon face.
Hubbell Hbl21Cm29 White 15A/20A 125V Straight Blade Female Plug To 20A 125V Twist Lock Locking Male Adapter - Hbl21Cm29 - 36-Hbl21Cm29F1
Permits use of 15 amp or 20 amp 125 volt straight blade plug with 20 amp 125 volt twist-lock locking type receptacle. Not recommended for use in wet locations.
Hubbell Hbl105Gf Yellow Watertight 30A Twist Lock To 15A Straight Blade Adapter With Gfci 30 - Hbl105Gf - 36-Hbl105Gff1
30 amp Twist-Lock to 15 amp straight blade adapter with GFCI. Now you can plug in your power drill, sander or any other 15 amp tool or appliance into that 30 amp outlet on the dock. Features manual reset button, high impact PVC housing - UV stabilized, sealed GFCI housing and keypad, and large LED power "on" light. Meets watertight requirements.
Hubbell Hbl105 Yellow Watertight 15A/20A 125V Straight Blade Female To 30A 125V Locking Plug Male Adapter - Hbl105 - 36-Hbl105F1
Fully molded, watertight design.
Hubbell Hbl104 Yellow Watertight 30A 125V Locking Female To 15A 125V Straight Blade Male Adapter - Hbl104 - 36-Hbl104F1
Fully molded, watertight design.
Hubbell Cwp26Crw Weatherproof Plate For Gfci Receptacle, White - Cwp26Crw - 36-Cwp26Crwf1
For ground fault receptacles and stylized receptacles. For vertical mounting in standard or FS/FD type boxes. PVC.
Hubbell Cwp26Cr Commercial Grade Weatherproof Lift Cover Plate For Gfci & Stylized Receptacles, Grey - Cwp26Cr - 36-Cwp26Crf1
For ground fault receptacles and stylized receptacles. For vertical mounting in standard or FS/FD type boxes. PVC.
Hubbell 50A 125/250V Vinyl Jacketed Pre Wired 50' Shore Power Cable Set - Hbl61Cm52W - 36-Hbl61Cm52Wf1
Vinyl jacketed. Completely factory pre-wired with molded-on devices. Connector end has a threaded sealing ring for making the inlet/connector interface watertight.LED models have two high density LED indicator lights. Bright green indicates "power on".
Hubbell 50A 125/250V Vinyl Jacketed Pre Wired 50' Shore Power Cable Set - Hbl61Cm52 - 36-Hbl61Cm52F1
Vinyl jacketed. Completely factory pre-wired with molded-on devices. Connector end has a threaded sealing ring for making the inlet/connector interface watertight.LED models have two high density LED indicator lights. Bright green indicates "power on".
Hubbell 50A 125/250 Volt Shore Power Inlet - Hbl504Ss - 36-Hbl504Ssf1
Mounting holes are 2-3/8" on centers and match existing mounting patterns. Mounting screws and gasket included.SS models have a gasketed, self-closing cover, making it watertight when fastened.
Hubbell 50A 125/250 Volt Shore Power Inlet - Hbl504Nm - 36-Hbl504Nmf1
Mounting holes are 2-3/8" on centers and match existing mounting patterns. Mounting screws and gasket included.Non-metallic (NM) models feature a UV resistant white cover which make the unit weatherproof when closed.
Hubbell 30A 125V Vinyl Jacketed Pre Wired Shore Power Cable Set - Hbl61Cm08 - 36-Hbl61Cm08F1
Vinyl jacketed. Completely factory pre-wired with molded on devices. Connector end has non-metallic threaded sealing ring which makes inlet/connector interface watertight.
Hubbell 30A 125V Vinyl Jacketed Pre Wired Shore Power Cable Set - Hbl61Cm03 - 36-Hbl61Cm03F1
Vinyl jacketed. Completely factory pre-wired with molded on devices. Connector end has non-metallic threaded sealing ring which makes inlet/connector interface watertight.
Gray Thermoplastic Fd Box - Hbl6083 - 36-Hbl6083F1
Type FD (deep). Molded ridge around face further prevents water from getting between box and cover plate. 4-9/16" high x 2-15/16" wide x 3-1/4" deep. Has a 22 cubic inch capacity.
Gfci Duplex Receptacle W/Cover Plate, White - Gfrst52Mw - 36-Gfrst52Mwf1
Hubbell's GFCI receptacles can be mounted on any standard 2.50" (63.5) deep box. A feed-thru feature provides protection not only at that receptacle but also at any other receptacle located downstream from it on the same circuit. These devices meet the requirements of The National Electric Code (NEC) and American Boat and Yacht Council Standard and will accept locking fork terminals.Caution: Ground Fault Receptacles should not be mounted in locations exposed to salt spray nor in the engine room. For GFCI protection of such locations, downstream feeding from an internally located Ground Fault Receptacle is recommended.
Gfci Duplex Receptacle W/Cover Plate, Ivory - Gfrst52Mi - 36-Gfrst52Mif1
Hubbell's GFCI receptacles can be mounted on any standard 2.50" (63.5) deep box. A feed-thru feature provides protection not only at that receptacle but also at any other receptacle located downstream from it on the same circuit. These devices meet the requirements of The National Electric Code (NEC) and American Boat and Yacht Council Standard and will accept locking fork terminals.Caution: Ground Fault Receptacles should not be mounted in locations exposed to salt spray nor in the engine room. For GFCI protection of such locations, downstream feeding from an internally located Ground Fault Receptacle is recommended.
Gfci Duplex Receptacle W/Cover Plate, Gray - Gfrst52Mgy - 36-Gfrst52Mgyf1
Hubbell's GFCI receptacles can be mounted on any standard 2.50" (63.5) deep box. A feed-thru feature provides protection not only at that receptacle but also at any other receptacle located downstream from it on the same circuit. These devices meet the requirements of The National Electric Code (NEC) and American Boat and Yacht Council Standard and will accept locking fork terminals.Caution: Ground Fault Receptacles should not be mounted in locations exposed to salt spray nor in the engine room. For GFCI protection of such locations, downstream feeding from an internally located Ground Fault Receptacle is recommended.
